Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM U

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  TERMINALS OF ECU  


TCM


C246463N01
2.844,0.323 3.24,0.563 0.396,0.24 4.219,0.323 4.615,0.563 0.396,0.24 2.948,0.365 3.385,0.74 0.438,0.375 10 E9 4.292,0.375 4.792,0.729 0.5,0.354 10 E10

HINT:

Each ECU terminal's standard voltage or resistance is shown in the table below.

In the table, first follow the information under "Condition". Look under "Symbols (Terminals No.)" for the terminals to be inspected. The standard voltage or resistance between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the ECU terminals.


Symbols (Terminals No.) Wiring Color Terminal Description Condition Specified Condition
E9-1 (BAT2) - E9-6 (E01) B - BR Battery (for ECU memory) Always 11 to 14 V
E9-2 (BAT) - E9-6 (E01) G - BR Battery (for ECU memory) Always 11 to 14 V
E9-3 (+B) - E9-6 (E01) L - BR Power source of ECM Ignition switch ON 11 to 14 V
E9-4 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω
E9-5 (E02) - Body ground BR - Body ground Ground Always Below 1 Ω
E9-6 (E01) - Body ground BR - Body ground Ground Always Below 1 Ω
E9-7 (CANH) - E9-4 (E1) R - BR *1
P - BR *2
CAN communication line Ignition switch ON Pulse generation
E9-8 (RENG) - E9-4 (E1) W-L - BR Engine speed signal Engine idling speed Pulse generation
(See waveform 1)
E9-11 (SPDO) - E9-4 (E1) L-W - BR Vehicle speed signal Vehicle speed 40 km/h (25 mph) Pulse generation
(See waveform 2)
E9-12 (MODE) - E9-4 (E1) *1 B-Y - BR 3 shift position indicator light signal Ignition switch ON with shift lever in 3 Below 1 V
Ignition switch ON with shift lever not in 3 11 to 14 V
E9-13 (W) - E9-4 (E1) *1 G-B - BR AT indicator light signal Ignition switch ON and AT indicator light on Below 1 V
Ignition switch ON and AT indicator light off 11 to 14 V
E9-16 (STR) - E9-4 (E1) B - BR Bypass terminal to P-N position switch Cranking Below 2 V
E9-17 (CANL) - E9-4 (E1) G - BR *1
LG - BR *2
CAN communication line Ignition switch ON Pulse generation
E9-20 (ODL) - E9-4 (E1) *1 LG-B - BR D shift position indicator signal Ignition switch ON with shift lever in D Below 1 V
Ignition switch ON with shift lever not in D 11 to 14 V
E9-21 (ODCS) - E9-4 (E1) R-B - BR 3 shift position switch signal Ignition switch ON with shift lever in 3 Below 1 V
Ignition switch ON with shift lever not in 3 11 to 14 V
E9-23 (R) - E9-4 (E1) W-R - BR R shift position switch signal Ignition switch ON with shift lever in R 11 to 14 V
Ignition switch ON with shift lever not in R Below 1 V
E9-24 (T) - E9-4 (E1) *1 V - BR Terminal ECUT of DLC3 Ignition switch ON 11 to 14 V
E10-2 (C3B+) - E10-1 (C3B-) V - B SL3 solenoid signal When electricity is turned on Pulse generation
(See waveform 3)
When electricity is not turned on Below 1 V
E10-4 (C2+) - E10-3 (C2-) LG - R SL2 solenoid signal When electricity is turned on Pulse generation
(See waveform 4)
When electricity is not turned on Below 1 V
E10-6 (B1+) - E10-5 (B1-) R-W - W-R SL1 solenoid signal When electricity is turned on Pulse generation
(See waveform 5)
When electricity is not turned on Below 1 V
E10-7 (VBOP) - E10-18 (EOPT) L-W - B-W Power source of output speed sensor Ignition switch ON 11 to 14 V
E10-8 (ROTP) - E10-18 (EOPT) B - B-W Output speed sensor signal Vehicle speed 20 km/h (12 mph) Pulse generation
(See waveform 6)
E10-9 (VBTB) - E10-20 (ETBN) G-W - R Power source of input speed sensor Ignition switch ON 11 to 14 V
E10-10 (RTBN) - E10-20 (ETBN) W - R Input speed sensor signal Engine idling speed with shift lever in P or N Pulse generation
(See waveform 7)
E10-11 (LUCR) - E9-4 (E1) L-R - BR SL solenoid signal When electricity is turned on 11 to 14 V
When electricity is not turned on Below 1 V
E10-12 (SOLR) - E9-4 (E1) W - BR SR solenoid signal When electricity is turned on 11 to 14 V
When electricity is not turned on Below 1 V
E10-14 (OTMP) - E10-13 (ETMP) P - G ATF temperature sensor signal ATF temperature: 80 °C (176°F) or more Below 1.1 V
ATF temperature: 20 °C (68°F) Approximately 3.4 V
E10-15 (P) - E9-4 (E1) LG - BR P shift position switch signal Ignition switch ON with shift lever in P Below 1 V
Ignition switch ON with shift lever not in P 11 to 14 V
E10-16 (2) - E9-4 (E1) L-W - BR 2 shift position switch signal Ignition switch ON with shift lever in 2 Below 1 V
Ignition switch ON with shift lever not in 2 11 to 14 V
E10-18 (EOPT) - E9-4 (E1) B-W - BR Output speed sensor ground Always Below 1 Ω
E10-20 (ETBN) - E9-4 (E1) R - BR Input speed sensor ground Always Below 1 Ω
E10-22 (LUCC) - E9-4 (E1) W-L - BR DSU solenoid signal Lock-up OFF Below 1 V
Slip lock-up (ON ←→ OFF) Pulse generation
(See waveform 8)
E10-23 (D) - E9-4 (E1) G-Y - BR D shift position switch signal Ignition switch ON with shift lever in D Below 1 V
Ignition switch ON with shift lever not in D 11 to 14 V
E10-24 (N) - E9-4 (E1) B-Y - BR N shift position switch signal Ignition switch ON with shift lever in N Below 1 V
Ignition switch ON with shift lever not in N 11 to 14 V
E10-25 (L) - E9-4 (E1) V - BR L shift position switch signal Ignition switch ON with shift lever in L Below 1 V
Ignition switch ON with shift lever not in L 11 to 14 V

*1: w/o Multi Information Display

*2: w/ Multi Information Display

a.
C143845N01
2.656,0.313 3.344,0.719 0.688,0.406 10 5 V/DIV 1.875,1.656 2.719,2.052 0.844,0.396 10 5 ms/DIV 2.906,1.021 3.385,1.344 0.479,0.323 10 GND

waveform 1

Terminal RENG - E1
Tool setting 5 V/DIV, 5 ms/DIV
Vehicle condition Engine idling speed (When the measured waveform is 1100 rpm)

HINT:

As the engine speed becomes higher, the frequency becomes shorter.



b.
C143846N01
2.656,0.333 3.344,0.76 0.688,0.427 10 5 V/DIV 1.74,1.656 2.771,2.052 1.031,0.396 10 10 ms/DIV 2.906,0.833 3.385,1.219 0.479,0.385 10 GND

Waveform 2

Terminal SPDO - E1
Tool setting 5 V/DIV, 10 ms/DIV
Vehicle condition Vehicle speed 40 km/h (25 mph)

HINT:

As the vehicle speed becomes higher, the frequency becomes shorter.



c.
C143847N01
2.656,0.333 3.354,0.74 0.698,0.406 10 5 V/DIV 1.875,1.656 2.74,2.052 0.865,0.396 10 1 ms/DIV 2.906,1.021 3.406,1.396 0.5,0.375 10 GND

Waveform 3

Terminal C3B+ - C3B-
Tool setting 5 V/DIV, 1 ms/DIV
Vehicle condition When electricity is turned on

HINT:

While shifting and adjusting the line pressure, the duty ratio becomes smaller.



d.
C143847N02
2.656,0.313 3.323,0.688 0.667,0.375 10 5 V/DIV 1.875,1.656 2.667,2.01 0.792,0.354 10 1 ms/DIV 2.906,1.031 3.396,1.344 0.49,0.313 10 GND

Waveform 4

Terminal C2+ - C2-
Tool setting 5 V/DIV, 1 ms/DIV
Vehicle condition When electricity is turned on

HINT:

During the shift, the duty ratio becomes smaller.



e.
C143847N03
2.656,0.323 3.344,0.677 0.688,0.354 10 5 V/DIV 1.875,1.656 2.625,2.021 0.75,0.365 10 1 ms/DIV 2.906,1.031 3.427,1.427 0.521,0.396 10 GND

Waveform 5

Terminal B1+ - B1-
Tool setting 5 V/DIV, 1 ms/DIV
Vehicle condition When electricity is turned on

HINT:

During the shift, the duty ratio becomes smaller.



f.
C143844N01
2.656,0.333 3.323,0.688 0.667,0.354 10 5 V/DIV 1.875,1.656 2.677,2.021 0.802,0.365 10 1 ms/DIV 2.906,1.042 3.396,1.365 0.49,0.323 10 GND

Waveform 6

Terminal ROTP - EOPT
Tool setting 5 V/DIV, 1 ms/DIV
Vehicle condition Vehicle speed 20 km/h (12 mph)

HINT:

As the output speed (vehicle speed) becomes higher, the frequency becomes shorter.



g.
C143843N01
2.656,0.333 3.302,0.677 0.646,0.344 10 5 V/DIV 1.875,1.656 2.667,2.021 0.792,0.365 10 1 ms/DIV 2.906,1.021 3.375,1.375 0.469,0.354 10 GND

Waveform 7

Terminal RTBN - ETBN
Tool setting 5 V/DIV, 1 ms/DIV
Vehicle condition Engine idling speed (When the measured waveform is 1360 rpm)

HINT:

As the turbine speed becomes higher, the frequency becomes shorter.



h.
C143861N01
2.76,0.302 3.427,0.646 0.667,0.344 10 5 V/DIV 1.979,1.635 2.781,1.969 0.802,0.333 10 5 ms/DIV 3.01,1.021 3.427,1.344 0.417,0.323 10 GND

Waveform 8

Terminal LUCC - E1
Tool setting 5 V/DIV, 5 ms/DIV
Vehicle condition Slip lock-up (ON ←→ OFF)

HINT:

When direct coupled lock-up, the duty ratio becomes 100 %.




ECM


HINT:

Each ECM terminal's standard voltage is shown in the table below.

In the table, first follow the information under "Condition". Look under "Symbols (Terminals No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration below as a reference for the ECM terminals.


A141508N02
3.406,0.583 3.802,0.823 0.396,0.24 1.719,0.583 2.115,0.823 0.396,0.24 5.167,0.583 5.563,0.823 0.396,0.24 3.479,0.635 3.969,1.01 0.49,0.375 10 C24 1.792,0.635 2.26,1 0.469,0.365 10 C23 5.271,0.635 5.688,0.979 0.417,0.344 10 E3

Symbols (Terminals No.) Wiring Color Terminal Description Condition Specified Condition
E3-24 (ATNE) - C24-32 (E1) W-L - W-B Engine speed signal Engine idling speed Pulse generation
E3-4 (CANH) - C24-32 (E1) R - W-B CAN communication line Ignition switch ON Pulse generation
E3-3 (CANL) - C24-32 (E1) G - W-B CAN communication line Ignition switch ON Pulse generation