Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM C

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0562  System Voltage Low  


DESCRIPTION

The battery supplies electricity to the TCM even when the ignition switch is in the OFF position. This power allows the TCM to store data such as DTC history, freeze frame data. If the battery voltage falls below a minimum level, these memories are cleared and the TCM determines that there is a malfunction in the power supply circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P0562 System Voltage Low Back-up power source (BAT, BAT2) is cut off for a specific period of time.
(1 trip detection logic)
·

Open or short in back-up power source circuit

·

TCM


Come on Blinks DTC stored

·

MIL:"Comes on" means the MIL (Malfunction IndicatorLamp) illuminates.

·

Memory:"DTC stored" means the TCM stores the trouble code if the ECU detects the DTC detection condition.


WIRING DIAGRAM

C246628E02
6.083,3.26 6.625,3.583 0.542,0.323 10 TCM 1.604,1.208 2.49,1.677 0.885,0.469 10 ECU-B 0.646,1.604 1.531,2.01 0.885,0.406 10 FL MAIN 0.75,2.479 1.719,2.885 0.969,0.406 10 BATTERY 5.781,1.792 6.365,2.146 0.583,0.354 10 BAT2 5.781,1.052 6.323,1.417 0.542,0.365 10 BAT 5.781,2.344 6.292,2.667 0.51,0.323 10 E01 6.094,3.115 6.469,3.427 0.375,0.313 10 E9 5.615,0.948 5.854,1.219 0.24,0.271 10 2 2,0.948 2.292,1.271 0.292,0.323 10 2 1.594,0.948 1.979,1.25 0.385,0.302 10 1 5.615,1.698 5.948,1.979 0.333,0.281 10 1 5.615,2.25 5.979,2.563 0.365,0.313 10 6

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK TCM (BAT, BAT2 VOLTAGE)
C246466C01
0.469,1.781 0.958,2.073 0.49,0.292 0.875,2.458 1.281,2.167 true 1.698,2.177 2.198,2.406 true 2.198,2.781 1.594,2.177 true 0.115,0.083 0.448,0.417 0.333,0.333 10 *a 0.333,2.365 1.042,2.698 0.708,0.333 10 6 (E01) 2.219,2.698 2.948,3.01 0.729,0.313 10 2 (BAT) 2.219,2.323 3.01,2.667 0.792,0.344 10 1 (BAT2) 0.604,1.833 0.99,2.135 0.385,0.302 10 E9
*a Rear view of wire harness connector
(to TCM)


a.

Disconnect the E9 TCM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
E9-1 (BAT2) - E9 - 6 (E01) Always 11 to 14 V
E9-2 (BAT) - E9 - 6 (E01) Always



d.

Reconnect the E9 TCM connector.

Result:
proceed to
OK
NG




OK

NG

2.CHECK HARNESS AND CONNECTOR (ECU-B FUSE - TCM)
2.CHECK HARNESS AND CONNECTOR (ECU-B FUSE - TCM)
a.

Remove the ECU-B fuse from the engine room relay block.


b.

Disconnect the E9 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):
Tester Connections Condition Specified Conditions
2 (ECU-B fuse) - E9-1 (BAT2) Always Below 1 Ω
2 (ECU-B fuse) - E9-2(BAT) Always


Standard resistance (Check for short):
Tester Connections Condition Specified Conditions
2 (ECU-B fuse) - Body ground Always 10 kΩ or higher



d.

Reconnect the E9 transmission connector.


e.

Reinstall the ECU-B fuse.

Result:
proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (ECU-B FUSE - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECU-B FUSE - BATTERY)
a.

Remove the ECU-B fuse from the engine room relay block.


b.

Disconnect the negative battery terminal.


c.

Disconnect the positive battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):
Tester Connections Condition Specified Conditions
Positive battery terminal - 1 (ECU-B fuse) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connections Condition Specified Conditions
1 (ECU-B fuse) - Body ground Always 10 kΩ or higher



e.

Reinstall the ECU-B fuse.


f.

Reconnect the positive battery terminal.


g.

Reconnect the negative battery terminal.

Result:
proceed to
OK
NG




OK

CHECK FOR INTERMITTENT PROBLEMS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR