Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM C

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0710  Transmission Fluid Temperature Sensor "A" Circuit  P0711  Transmission Fluid Temperature Sensor Circuit Range / Performance  


DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input to the TCM.

The sensor resistance changes with the transmission fluid temperature. As the temperature rises, the sensor resistance decreases. The TCM applies a voltage to the temperature sensor through TCM terminal OTMP, and the TCM calculates the fluid temperature based on the voltage signal.

HINT:

The ATF temperature is likely to increase under conditions such as towing, climbing hills and in heavy traffic.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P0710 Transmission Fluid Temperature Sensor "A" Circuit ATF temperature sensor circuit becomes open or short for a specific period of time.
(1 trip detection logic)
·

Open or short in ATF temperature sensor circuit

·

Solenoid wire (ATF temperature sensor)

·

TCM


Come on Blinks DTC stored
P0711 Transmission Fluid Temperature Sensor Circuit Range / Performance ATF temperature sensor does not operate correctly.
(2 trip detection logic)
·

Solenoid wire (ATF temperature sensor)

·

TCM


Come on Blinks DTC stored

·

MIL:"Comes on" means the MIL (Malfunction IndicatorLamp) illuminates.

·

Memory:"DTC stored" means the TCM stores the trouble code if the ECU detects the DTC detection condition.


WIRING DIAGRAM

C246489E02
0.229,1.896 2.135,2.635 1.906,0.74 10 ECT SOLENOID (ATF TEMPERATURE SENSOR) 6.021,1.365 6.594,1.688 0.573,0.323 10 ETMP 6.021,0.615 6.615,1 0.594,0.385 10 OTMP 6.354,2 6.844,2.323 0.49,0.323 10 TCM 1.708,1.26 2.135,1.635 0.427,0.375 10 H9 0.24,1.729 0.844,2.115 0.604,0.385 10 E21 6.365,1.833 6.781,2.208 0.417,0.375 10 E10 1.708,0.521 2.083,0.823 0.375,0.302 10 H5 5.771,0.521 6.177,0.813 0.406,0.292 10 14 5.771,1.26 6.094,1.625 0.323,0.365 10 13 2,0.521 2.385,0.875 0.385,0.354 10 8 1.99,1.26 2.396,1.583 0.406,0.323 10 12

PROCEDURE

1.INSPECT SOLENOID WIRE (ATF TEMPERATURE SENSOR)
C130158C01
1.448,1.448 0.948,1.323 true 1.448,1.573 0.948,1.688 true 0.083,0.063 0.427,0.344 0.344,0.281 10 *a 0.49,1.25 1.052,1.583 0.563,0.333 10 8 (H5) 0.396,1.615 1.083,2 0.688,0.385 10 12 (H9)
*a Front view of wire harness connector
(to Solenoid wire)


a.

Disconnect the E21 solenoid wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition(ATF Temperature) Specified Condition
8 (H5) - 12 (H9) 0°C (32°F) 5.07 kΩ to 6.19 kΩ
140°C (284°F) 69.8 Ω to 74.2 Ω
8 (H5) or 12 (H9) - Body ground - 10 kΩ or higher


HINT:

If the resistance is outside the specified range at either of the ATF temperatures shown in the table below, the driveability of the vehicle may be affected.


Standard resistance:
ATF Temperature Specified Condition
20°C (68°F) 2.4 kΩ
80°C (176°F) 313 Ω



c.

Reconnect the E3 solenoid wire connector.

Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (SOLENOID WIRE - TCM)

NG

REPAIR OR REPLACE SOLENOID WIRE

2.CHECK HARNESS AND CONNECTOR (SOLENOID WIRE - TCM)
a.

Disconnect the E10 TCM connector.


b.

Measure the resistance.

Standard resistance:
Tester Connection Condition(ATF Temperature) Specified Condition
E10-14 (OTMP) - E10-13 (ETMP) 0°C (32°F) 5.07 kΩ to 6.19 kΩ
140°C (284°F) 69.8 Ω to 74.2 Ω
E10-14 (OTMP) or E10-13 (ETMP) - Body ground - 10 kΩ or higher


HINT:

If the resistance is outside the specified range at either of the ATF temperatures shown in the table below, the driveability of the vehicle may be affected.


Standard resistance:
ATF Temperature Specified Condition
20°C (68°F) 2.4 kΩ
80°C (176°F) 313 Ω



c.

Reconnect the E10 TCM connector.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR