Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM D

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  MECHANICAL SYSTEM TESTS  


STALL SPEED TEST


HINT:

This test is to check the overall performance of the engine and transmission by measuring the stall speeds in D and R.


CAUTION:
·

To ensure safety, perform this test in a wide, clear level area which provides good traction.

·

The stall speed test must always be carried out by pairs of technicians. One technician must watch the wheels and wheel stoppers from outside the vehicle to make sure they do not slip, while the other performs the test.



NOTICE:

Do not perform the stall speed test for longer than 5 seconds.


a.

Connect the intelligent tester to the DLC3.


b.

Run the vehicle until the ATF (Automatic Transmission Fluid) temperature reaches 70 to 90°C (158 to 194°F).

Powertrain > ECT > Data List
Tester Display
A/T Oil Temperature 1
50003 565 24

c.

Allow the engine to idle with the air conditioning OFF.

Idling speed:

750 rpm



d.

Chock all wheels.


e.

Set the parking brake and keep the brake pedal firmly depressed with your left foot.


f.

Move the shift lever to D.


g.

Depress the accelerator pedal all the way down with your right foot.


h.

Read the engine rpm (stall speed) and release the accelerator pedal immediately.

Standard value:

2100 to 2600 rpm



i.

Perform the same test in R.

Standard value:

2100 to 2600 rpm


Evaluation:
Test Result Possible Cause
Stall speeds in D and R are same, but lower than standard value.
·

Engine power is insufficient

·

torque converter assembly is faulty


Stall speeds in D and R positions are same, but higher than standard value.
·

Line pressure is too low

·

Improper fluid level

·

torque converter assembly is faulty

·

1st and reverse brake (B2) is slipping

·

Reverse clutch (C1) is slipping

·

Forward clutch (C2) is slipping


Stall speed in D is higher than standard value.
·

Line pressure is too low

·

Forward clutch (C2) is slipping

·

torque converter assembly is faulty


Stall speed in R is higher than standard value.
·

Line pressure is too low

·

Reverse clutch (C1) is slipping

·

1st and reverse brake (B2) is slipping





SHIFT TIME LAG TEST


HINT:

When the shift lever is shifted while the engine is idling, there will be a certain time lag before the shock can be felt. This is used for checking the condition of the clutch and brake.


a.

Connect the intelligent tester to the DLC3.


b.

Run the vehicle until the ATF (Automatic Transmission Fluid) temperature reaches 70 to 90°C (158 to 194°F).

Powertrain > ECT > Data List
Tester Display
A/T Oil Temperature 1
50003 565 24

c.

Allow the engine to idle with the air conditioning OFF.

Idling speed:

750 rpm



d.

Set the parking brake and keep the brake pedal firmly depressed with your left foot.


e.

Check the D position time lag.

i.

Move the shift lever to N and wait for 1 minute. (*1)


ii.

Move the shift lever to D and measure the time until the shock is felt. (*2)


iii.

Repeat procedures (*1) and (*2) three times, and calculate the average time of the three tests.



f.

Check the R position time lag.

i.

Move the shift lever to N and wait for 1 minute. (*3)


ii.

Move the shift lever to R and measure the time until the shock is felt. (*4)


iii.

Repeat procedures (*3) and (*4) three times, and calculate the average time of the three tests.

Standard value:

D position time lag is less than 1.0 second

R position time lag is less than 1.0 second


Evaluation :
Test Result Possible Cause
D position time lag exceeds standard value
·

Line pressure is too low

·

Forward clutch (C2) is worn


R position time lag exceeds standard value
·

Line pressure is too low

·

Reverse clutch (C1) is worn

·

1st and reverse brake (B2) is worn