Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM D

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  HYDRAULIC TEST  


PERFORM HYDRAULIC TEST


CAUTION:

The line pressure test should always be carried out in pairs. One technician should observe the conditions of the wheels and wheel stoppers from outside the vehicle, while the other is doing the test.


NOTICE:
·

Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature 70 to 90°C (158 to 194°F).

·

Be careful to prevent SST hose from interfering with the exhaust pipe.

·

This check must be conducted after checking and adjusting the engine.

·

Use a new gasket for SST and measuring instrument.

·

Perform under condition that A/C is OFF.

·

When conducting a stall test, do not continue more than 5 seconds.

·

Test plugs cannot be reused.



a.
C130160E04
1.406,3.208 1.208,3.417 true 0.948,2.073 0.875,2.406 true 1.667,1.875 1.865,2.531 true 2.813,0.771 2.083,1.198 true 2.156,2.552 1.74,1.813 true 1.688,0.615 1.365,0.875 true 1.448,0.292 1.094,1.76 true 1.042,0.344 1,1.833 true 2.698,3.281 3.229,3.667 0.531,0.385 10 SST 1.031,3.438 1.5,3.771 0.469,0.333 10 SST 0.76,2.427 1.208,2.813 0.448,0.385 10 C1 1.875,2.583 2.271,2.906 0.396,0.323 10 B1 2.865,0.667 3.25,0.979 0.385,0.313 10 B2 2.188,2.594 2.594,2.969 0.406,0.375 10 C2 1.708,0.5 2.719,0.865 1.01,0.365 10 Lock-up ON 1.469,0.146 2.573,0.573 1.104,0.427 10 Lock-up OFF 1.083,0.167 1.531,0.479 0.448,0.313 10 C3

Pressure gauge installation procedure.

i.

Warm up the ATF.


ii.

Remove the test plug on the left side of the transmission case and connect SST.

SST
09325-87201  09992-00095  (09992-00271)



b.

Inspect C2 pressure.

i.

Set the parking brake and chock.


ii.

Start the engine.


iii.

Keep your left foot pressed firmly on the brake pedal and move the shift lever to D.


iv.

Depress the accelerator pedal all the way down. Quickly read the highest hydraulic pressure when the engine speed reaches stall speed.



c.

Inspect C1 pressure and B2 pressure

i.

Set the parking brake and chocks.


ii.

Start the engine.


iii.

Keep your left foot pressed firmly on the brake pedal and move the shift lever to R.


iv.

Depress the accelerator pedal all the way down. Quickly read the highest hydraulic pressure when the engine speed reaches stall speed.



d.

Inspect B1 pressure

i.

Jack up 4 wheels and support the vehicle with a rigid rack.


ii.

Start the engine.


iii.

Move the shift lever to D and gradually depress the accelerator pedal to change the gear into 2nd. Measure the hydraulic pressure at 2000 rpm of engine speed.



e.

Inspect C3 pressure

i.

Jack up 4 wheels and support the vehicle with a rigid rack.


ii.

Start the engine.


iii.

Move the shift lever to D and gradually depress the accelerator pedal to change the gear into 3rd. Measure the hydraulic pressure with the pedal released.



f.

Inspect Lock-up OFF pressure

i.

Jack up 4 wheels and support the vehicle with a rigid rack.


ii.

Start the engine.


iii.

Move the shift lever to D and measure the hydraulic pressure (hydraulic pressure when lock-up is OFF).


iv.

Gradually depress the accelerator pedal to change the gear into O/D. Further accelerate and measure the hydraulic pressure with the gear locked-up. (hydraulic pressure when lock-up is ON)

HINT:

Under the condition that the vehicle speed is approximately 62 to 77 km/h (39 to 48 mph) and throttle angle is 5 to 20 %, the O/D lock-up turns ON.


Specified hydraulic pressure:
Item Shift Position Condition Specified Condition
C2 D Stall test 930 to 1120 kPa
(9.5 to 11.4 kgf/cm2, 135 to 162 psi)
C1, B2 R Stall test 1520 to 2110 kPa
(15.5 to 21.5 kgf/cm2, 220 to 306 psi)
C3 D 3rd gear and accelerator pedal fully released (Lock-up OFF) 440 to 640 kPa
(4.5 to 6.5 kgf/cm2, 64 to 93 psi)
B1 D 2nd gear and engine speed 2000 rpm 930 to 1130 kPa
(9.5 to 11.5 kgf/cm2, 135 to 164 psi)
Lock up OFF D When Lock-up OFF 590 to 750 kPa
(6.0 to 7.6 kgf/cm2, 86 to 109 psi)
When Lock-up ON 20 or less kPa
(0.2 or less kgf/cm2, 2.9 or less psi)


Evaluation:
Problem Possible Cause
Measured values are higher than specified values in all positions Shift solenoid valve defective
Measured values are lower than specified values in all positions
·

Shift solenoid valve defective

·

Oil pump defective


Pressure is low in D only
·

D position circuit fluid leak

·

Forward clutch (C2) defective


Pressure is low in R only
·

R position circuit fluid leak

·

Reverse clutch (C1) defective

·

1st and reverse brake (B2) defective