Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM U

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  FAIL-SAFE CHART  


FAIL-SAFE


a.

Fail-safe function:

The fail-safe function operates to maintain vehicle drivability as much as possible even when a malfunction occurs in the input/output signal system in the TCM.

If the system returns to normal after a malfunction is detected, the fail-safe function is cancelled, but the diagnostic results remain stored.

The AT indicator light blinks during fail-safe operation.

DTC No. Detection Item Fail-safe control Release condition of fail-safe control
P0562 System Voltage Low When a malfunction is detected, hold in 3rd. After the system condition returns to normal, turn the ignition switch off.
P0642 Sensor Reference Voltage "A" Circuit Low
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) Perform normal gear change controlling as the shift lever in D. The system condition returns to normal.
Transmission Range Sensor Circuit Malfunction (PRNDL Input)
P0710 Transmission Fluid Temperature Sensor "A" Circuit When a malfunction is detected, shift into the 3rd and then shift into the 1st to 3rd depending on the vehicle speed and throttle opening angle. After the system condition returns to normal, shift into P or N when the vehicle speed is 0 km/h.
P0711 Transmission Fluid Temperature Sensor Circuit Range / Performance
P0722 Output Speed Sensor Circuit No Signal
·

If the malfunction is in the sensor system, keep the gear position just before the malfunction is detected and if the vehicle stops, hold in 1st.

·

If the malfunction is in the automatic transmission assembly, hold in 1st.


·

If the trouble is in the sensor system, after the system condition returns to normal, shift into P or N when the vehicle speed is 0 km/h.

·

If the trouble is in the automatic transmission assembly, after the system condition returns to normal, turn the ignition switch off.


P0725 Engine Speed Input Circuit When a malfunction is detected, shift into the 3rd and then shift into the 1st to 3rd depending on the vehicle speed and throttle opening angle. After the system condition returns to normal, shift into P or N when the vehicle speed is 0 km/h.
P0741 Lock up Speed is not Conformable Prohibit locking up. After the system condition returns to normal, shift into P or N when the vehicle speed is 0 km/h.
P0743 Shift Solenoid "E" Electrical
(Shift Solenoid Valve SL)
·

Prohibit electricity from flowing into the malfunctioning solenoid.

·

When the type of trouble is a short circuit, shift into the 1st to 3rd using a normal solenoid. However, if a short circuit has occurred in the SL3 solenoid and SR solenoid, hold in 3rd.

·

When the type of trouble is open circuit or the trouble exists in at least 2 solenoids, hold in 3rd.


After the system condition returns to normal, turn the ignition switch off.
P0748 Shift Solenoid "A" Electrical
(Shift Solenoid Valve SL1)
P0773 Shift Solenoid "F" Electrical
(Shift Solenoid Valve SR)
P0778 Shift Solenoid "B" Electrical
(Shift Solenoid Valve SL2)
P0798 Shift Solenoid "C" Electrical
(Shift Solenoid Valve SL3)
P2759 Shift Solenoid "D" Electrical
(Shift Solenoid Valve DSU)
P2767 Input / Turbine Speed Sensor "A" Circuit When a malfunction is detected, shift into the 3rd and then shift into the 1st to 3rd depending on the vehicle speed and throttle opening angle. After the system condition returns to normal, shift into P or N when the vehicle speed is 0 km/h.
U0100 Lost Communication with ECM / PCM "A"
·

Make the throttle angle and the engine torque a constant value.

·

When trouble is detected, shift into 3rd and then shift into the 1st to 3rd depending on the vehicle speed.


After the system condition returns to normal, shift into P or N when the vehicle speed is 0 km/h.