Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015086 AUTOMATIC TRANSMISSION UNIT G

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  INSPECTION  


PROCEDURE

Hide 35108B 1.INSPECT RADIAL BALL BEARING

a.
C153983

Check the radial ball bearing whether it is rough or worn.

If necessary, replace the radial ball bearing.


Hide 35301 2.INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY

Hide 35610 3.INSPECT FRONT MULTIPLE DISC CLUTCH ASSEMBLY

a.
C154027

Using a feeler gauge, measure the forward clutch piston stroke.

Piston stroke:

0.33 to 1.27 mm (0.0130 to 0.0500 in.)


If the piston stroke is greater than the maximum, replace the front multiple disc clutch assembly.


b.
C154026

Using a feeler gauge, measure the reverse clutch piston stroke.

Piston stroke:

0.67 to 0.98 mm (0.0264 to 0.0386 in.)


If the piston stroke is greater than the maximum, replace the front multiple disc clutch assembly.


c.
C154028

Using a dial indicator, measure the inside diameter of the front multiple disc drum.

Standard inside diameter:

44.50 to 44.52 mm (1.7520 to 1.7528 in.)


Maximum inside diameter:

44.58 mm (1.7551 in.)


If the inside diameter is greater than the maximum, replace the front multiple disc clutch assembly.


d.
C154034

Install the forward clutch hub into the front multiple disc drum.


e.

Turn the forward clutch hub, and check that the clutch discs rotate smoothly.


f.
C154035

Install the front planetary sun gear sub-assembly into the front multiple disc drum.


g.

Turn the front planetary sun gear sub-assembly, and check that the clutch discs rotate smoothly.


Hide 35650 4.INSPECT REAR MULTIPLE DISC CLUTCH ASSEMBLY

a.
C154036

Using a feeler gauge, measure the rear clutch piston stroke.

Piston stroke:

1.20 to 1.51 mm (0.0472 to 0.0594 in.)


If the piston stroke is greater than the maximum, replace the rear multiple disc clutch assembly.


b.
C154037

Install the intermediate shaft sub-assembly into the rear multiple disc drum.


c.

Turn the intermediate shaft sub-assembly, and check that the clutch discs rotate smoothly.


Hide 35633B 5.INSPECT NO. 1 CLUTCH DISC

a.
C270801

Check if the sliding surfaces of the No. 1 clutch discs, No. 1 clutch plates and reverse clutch flange are worn or burnt. If necessary, replace them.

HINT:

Before assembling new No. 1 clutch discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35633F 6.INSPECT NO. 2 CLUTCH DISC

a.
C270801

Check if the sliding surfaces of the No. 2 clutch discs, No. 2 clutch plates and forward clutch flange are worn or burnt. If necessary, replace them.

HINT:

Before assembling new No. 2 clutch discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35673 7.INSPECT REAR CLUTCH DISC

a.
C184859

Check if the sliding surfaces of the rear clutch flanges, rear clutch discs, No. 3 clutch plate and rear clutch cushion plate are worn or burnt. If necessary, replace them.

HINT:

Before assembling new rear clutch discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35706U 8.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C153984

Using a dial indicator, measure the inside diameter of the planetary sun gear bushing.

Maximum inside diameter:

27.07 mm (1.0657 in.)


If the inside diameter is greater than the maximum, replace the planetary sun gear sub-assembly.


Hide 35709L 9.INSPECT REAR PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C153985

Using a dial indicator, measure the inside diameter of the rear planetary sun gear bushings.

Maximum inside diameter:

18.07 mm (0.7114 in.)


If the inside diameter is greater than the maximum, replace the rear planetary sun gear sub-assembly.


Hide 35681 10.INSPECT NO. 1 BRAKE DISC

a.
C153986

Check if the sliding surfaces of the No. 1 brake discs, brake plates and No. 1 brake flange are worn or burnt. If necessary, replace them.

HINT:

Before assembling new No. 1 brake discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35790E 11.INSPECT 1 WAY CLUTCH ASSEMBLY

a.
C153987C02
1.104,0.802 0.802,0.865 false 1.708,0.833 2.229,0.615 true 1.479,0.083 2.031,0.583 0.552,0.5 10 *b 2.26,0.531 2.781,0.979 0.521,0.448 10 *d 0.896,0.198 1.375,0.677 0.479,0.479 10 *a 0.615,0.771 1.073,1.24 0.458,0.469 10 *c
*a Lock
*b Free
*c Hold
*d Turn


Hold the planetary gear and turn the hub. The hub should turn freely clockwise and should lock counterclockwise.

If necessary, replace the 1 way clutch assembly.


Hide 35666B 12.INSPECT BRAKE CLUTCH DISC

a.
C153988

Check if the sliding surfaces of the brake clutch discs, brake plates and brake flanges are worn or burnt. If necessary, replace them.

HINT:

Before assembling new brake clutch discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35740 13.INSPECT FRONT PLANETARY RING GEAR ASSEMBLY

a.
C153989

Using a dial indicator, measure the inside diameter of the front planetary ring gear assembly.

Maximum inside diameter:

13.07 mm (0.5146 in.)


If the inside diameter is greater than the maximum, replace the front planetary ring gear assembly.