Home › Drivetrain › CLUTCH › CLUTCH PEDAL(for 3SZ-VE) › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002984 CLUTCH _0015091 CLUTCH PEDAL(for 3SZ-VE) N

CLUTCH  CLUTCH PEDAL(for 3SZ-VE)  ADJUSTMENT  


PROCEDURE

Hide 31301 1.INSPECT AND ADJUST CLUTCH PEDAL HEIGHT

a.

Pull back the floor carpet.


b.
C246087C02
1.521,0.833 1.938,0.292 true 1.771,1.365 2.063,1.469 true 1.969,0.177 2.177,0.354 0.208,0.177 10 *a 2.115,1.448 2.344,1.615 0.229,0.167 10 *b 2.583,3.969 2.823,4.146 0.24,0.177 10 *d 1.958,3.823 2.167,4 0.208,0.177 10 *c
*a Push Rod and Free Play Adjustment Point
*b Pedal Height Adjustment Point
*c Push Rod Play
*d Pedal Height


Check that the pedal height is correct.

Pedal height from asphalt sheet:

164.1 mm (6.461 in.)



c.

Adjust the pedal height.

i.

Loosen the lock nut and turn the stopper bolt until the height is correct. Tighten the lock nut.

Torque:
20 N*m (201 kgf*cm, 15 ft.*lbf)



Hide 2.INSPECT AND ADJUST PEDAL FREE PLAY AND PUSH ROD PLAY

a.

Check that the pedal free play and push rod play are correct.

i.

Depress the pedal until the clutch resistance begins to be felt.

Pedal free play:

3.0 to 20.0 mm (0.118 to 0.787 in.)



ii.

Gently depress the pedal until the resistance begins to increase a little.

Push rod play at pedal top:

1.0 to 8.0 mm (0.039 to 0.315 in.)




b.
D031462C02
1.833,1.615 2.031,1.76 0.198,0.146 10 *a 1.875,1.927 2.083,2.083 0.208,0.156 10 *b
*a Push Rod Play
*b Pedal Free Play


Adjust the pedal free play and push rod play.

i.

Loosen the lock nut and turn the push rod until the free play and push rod play are correct.


ii.

Tighten the lock nut.


iii.

After adjusting the pedal free play, check the pedal height.



Hide 3.INSPECT CLUTCH RELEASE POINT

a.
CL00512C03
1.552,1.604 2.104,1.021 true 0.844,1.563 1.26,1.552 true 1.323,1.104 1.5,1.302 0.177,0.198 10 *b 1.74,1.948 1.917,2.146 0.177,0.198 10 *d 2.135,0.885 2.302,1.083 0.167,0.198 10 *c 0.625,1.469 0.813,1.698 0.188,0.229 10 *a
*a Full Stroke end Position
*b From Pedal Stroke end Position to Release Point
*c Release Point
*d Pedal Stroke


Check the clutch release point.

i.

Pull the parking brake lever and chock the wheels.


ii.

Start the engine and allow it to idle.


iii.

Without depressing the clutch pedal, slowly move the shift lever into the reverse position until the gears engage.


iv.

Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

Standard distance:

25 mm (0.984 in.) or more

(From pedal stroke end position to release point)


Pedal stroke(Reference):

142.5 mm (5.610 in.)


If the distance is not as specified, perform the following operations.

·

Check the pedal height.

·

Check the push rod play and pedal free play.

·

Bleed the clutch line.

·

Check the clutch cover assembly and disc assembly.