Home › Drivetrain › CLUTCH › CLUTCH PEDAL(for K3-VE) › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002984 CLUTCH _0015092 CLUTCH PEDAL(for K3-VE) N

CLUTCH  CLUTCH PEDAL(for K3-VE)  ADJUSTMENT  


PROCEDURE

Hide 31301 1.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY

C150627C02
1.417,1.729 1.177,1.729 false 1.813,3.49 2.031,3.667 0.219,0.177 10 *a 1.458,1.656 1.688,1.844 0.229,0.188 10 *1
*1 Stopper Bolt
*a Pedal Height


a.

Turn back the floor carpet to expose the asphalt sheet under the pedal.


b.

Check that the pedal height is correct using a vernier caliper.

Standard:
for LHD:

168.0 mm (6.614 in.)

for RHD:

167.9 mm (6.610 in.)



c.

Adjust the pedal height.

i.

Loosen the lock nut and turn the stopper bolt until the correct pedal height is obtained.


ii.

Tighten the lock nut.

Torque:
20 N*m (201 kgf*cm, 15 ft.*lbf)



Hide 2.INSPECT AND ADJUST CLUTCH PEDAL FREE PLAY

C151156C02
2.458,1.875 2.625,2.042 0.167,0.167 10 *a
*a Pedal Free Play


a.

Lightly push the pedal by hand and check that the pedal free play is correct.

Standard:

15 to 25 mm (0.591 to 0.984 in.)



b.
C150628C02
1.635,0.667 2.031,0.917 false 2.052,1.75 2.427,1.469 false 1.458,0.573 1.667,0.74 0.208,0.167 10 *1 1.865,1.698 2.063,1.865 0.198,0.167 10 *2
*1 Nut
*2 Grommet


Adjust the pedal free play.

i.

Pull the clutch outer cable towards the front of the vehicle. Stop pulling the cable when the clutch release bearing hub touches the clutch cover diaphragm spring.


ii.

Turn the adjusting nut until the clearance between the nut and the grommet is between 3 to 6 mm (0.118 to 0.236 in.).


iii.

Align the protruding part of the grommet with the closest recess of the adjusting nut and set them in that position.


iv.

Check that clutch pedal free play is within the specified range.



Hide 3.INSPECT CLUTCH RELEASE POINT

CL00512C04
1.552,1.604 2.104,1.021 true 0.875,1.563 1.292,1.552 true 1.313,1.125 1.49,1.323 0.177,0.198 10 *b 1.74,1.948 1.917,2.146 0.177,0.198 10 *d 2.135,0.906 2.302,1.104 0.167,0.198 10 *c 0.656,1.49 0.844,1.719 0.188,0.229 10 *a
*a Full Stroke end Position
*b From Pedal Stroke end Position to Release Point
*c Release Point
*d Pedal Stroke


a.

While the engine is idling, ensure the parking brake is engaged with the brake pedal depressed. Under this condition, move the shift lever into first gear and gradually release the clutch pedal. Inspect the pedal stroke distance from the full stroke end position to the point immediately before the clutch is engaged (release point).

Standard:

25 mm (0.984 in.) or more

(From pedal stroke end position to release point)


Pedal stroke (Reference):

150 mm (5.905 in.)


If the distance is not as specified, perform the following operations.

·

Check the pedal height

·

Check the pedal free play

·

Check the clutch release cable

·

Check the clutch cover and the clutch disc