Home › Drivetrain › M5S MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION UNIT › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002985 M5S MANUAL TRANSMISSION / TRANSAXLE _0015106 MANUAL TRANSMISSION UNIT A

M5S MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 31111B 1.REMOVE CLUTCH HOUSING PLUG

a.

Remove the clutch housing plug from the clutch housing.


Hide 83181G 3.REMOVE SPEEDOMETER SENSOR (w/o ABS)

C229298

a.

Remove the bolt and speedometer sensor from the extension housing sub-assembly.


Hide 33403S 4.REMOVE SPEEDOMETER SENSOR HOLE PLUG (w/ ABS)

C249006

a.

Remove the bolt and speedometer sensor hole plug from the extension housing sub-assembly.


b.

Remove the O-ring from the speedometer sensor hole plug.


Hide 33283H 5.REMOVE FILLER PLUG

C150553

a.

Remove the filler plug and gasket from the extension housing sub-assembly.


Hide 33283H 6.REMOVE DRAIN PLUG

a.

Remove the drain plug and gasket from the extension housing sub-assembly.


Hide 33103 7.REMOVE EXTENSION HOUSING SUB-ASSEMBLY

a.
C200392C03
2.625,0.531 2.896,0.531 false 2.917,0.438 3.094,0.604 0.177,0.167 10 *1
*1 Wire Harness Clamp Bracket


Remove the 6 bolts and wire harness clamp bracket.


b.
C150555

Carefully tap the projection of the extension housing sub-assembly.

NOTICE:

Do not damage the extension housing sub-assembly.



Hide 33449B 8.REMOVE TRANSMISSION MAGNET

C150556

a.

Remove the transmission magnet from the manual transmission case.


Hide 33323 9.REMOVE OUTPUT SHAFT OIL SLINGER

C150557

a.

Remove the output shaft oil slinger from the manual transmission case.


Hide 33151 10.REMOVE OUTPUT SHAFT REAR BEARING RETAINER

C150558

a.

Remove the 3 bolts and output shaft rear bearing retainer.


Hide 33528B 11.REMOVE CONTROL SHAFT COVER

C150559

a.

Remove the 4 bolts, 2 washers, control shaft cover and gasket from the manual transmission case.


Hide 33284B 12.REMOVE REVERSE RESTRICT PIN HOLDER

C150560

a.

Remove the reverse restrict pin holder and gasket.


Hide 33295A 13.REMOVE REVERSE RESTRICT SHAFT

C152795

a.

Remove the bolt and gasket.


b.
C152797

Remove the reverse restrict shaft, reverse restrict cam and spring from the manual transmission case.


Hide 33203 14.REMOVE NO. 1 SHIFT LEVER SHAFT SUB-ASSEMBLY

C151163

a.

Using a pin punch (5 mm) and hammer, remove the slotted spring pin.


b.

Remove the No. 1 shift lever shaft sub-assembly and No. 1 shift lever inner .


c.

Remove the boot from the manual transmission case.


Hide 33111 15.REMOVE MANUAL TRANSMISSION CASE

C150562

a.

Using a snap ring expander, remove the snap ring from the output shaft.


b.
C150563

Using a hexagon socket wrench (6 mm), remove the hexagon bolt of the reverse idler gear shaft and gasket.


c.
C150564C03
2.198,0.979 2.406,0.792 false 2.458,0.698 2.688,0.875 0.229,0.177 10 *1
*1 Wire Harness Clamp Bracket


Remove the 8 bolts and wire harness clamp bracket from the manual transmission case.


d.
C150565

Remove the 2 bolts from the clutch housing.


e.
C267832

Using a plastic-faced hammer, tap out the manual transmission case.

NOTICE:

Do not damage the manual transmission case.



Hide 33321 16.REMOVE OUTPUT SHAFT

a.
C150568

Remove the output shaft.


b.
C150570

Remove the input shaft bearing and the wave spring from the input shaft.


Hide 33244D 17.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

A203680

a.

Remove the 3 bolts, gaskets, springs and balls from the clutch housing.


b.
C150572

Using a pin punch (5 mm) and hammer, remove the 2 slotted spring pins from the No. 3 gear shift fork shaft.


c.

Remove the No. 3 gear shift fork shaft, No. 3 gear shift fork and reverse head.


Hide 33242 18.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

C150573

a.

Using a pin punch (5 mm) and hammer, remove the 2 slotted spring pins from the No. 1 gear shift fork shaft.


b.

Remove the No. 1 gear shift fork shaft, No. 1gear shift fork and No. 1 gear shift head.


Hide 33243A 19.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

C150574

a.

Using a pin punch (5 mm) and hammer, remove the 2 slotted spring pins from the No. 2 gear shift fork shaft.


b.

Remove the No. 2 gear shift fork shaft, No. 2 gear shift fork and No. 2 gear shift head.


Hide 33221 20.REMOVE REVERSE SHIFT ARM SUB-ASSEMBLY

C150575

a.

Remove the spring from the reverse shift arm sub-assembly.


b.
C150576

Remove the 3 bolts and reverse shift arm sub-assembly.


Hide 33266C 21.REMOVE SHIFT INTER LOCK PLATE

C150577

a.

Remove the 2 shift inter lock plates from the clutch housing.


Hide 33402 22.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

C150578

a.

Remove the reverse idler gear sub-assembly, reverse idler gear thrust washer and reverse idler gear shaft from the clutch housing.


Hide 33326 23.REMOVE BEARING LOCK PLATE

C150579

a.

Remove the 3 bolts and bearing lock plate.


Hide 33311 24.REMOVE INPUT SHAFT

C150580

a.

Remove the input shaft and counter gear from the clutch housing.


Hide 33256 25.REMOVE SELECT INNER LEVER

C150581

a.

Using a pin punch (5 mm ) and hammer, remove the slotted spring pin.


b.

Remove the select lever shaft sub-assembly, select inner lever and spring.


c.
C150582

Using a screwdriver, remove the oil seal from the control shaft cover.

NOTICE:

Be careful not to damage the control shaft cover.



Hide 33111Q 26.REMOVE CLUTCH HOUSING OIL SEAL

C150583

a.

Using a screwdriver, remove the clutch housing oil seal from the clutch housing.

NOTICE:

Be careful not to damage the clutch housing.



Hide 33111Y 27.REMOVE TRANSMISSION CASE OIL SEAL

C150584

a.

Using a screwdriver and hammer, remove the transmission case oil seal from the manual transmission case.


Hide 33103R 28.REMOVE MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL

C150585

a.

Using a screwdriver, remove the manual transmission extension housing oil seal from the extension housing sub-assembly.


Hide 33257B 29.REMOVE GEAR OIL PLATE

C150586

a.

Remove the bolt and gear oil plate from the extension housing sub-assembly.