Home › Drivetrain › M5S MANUAL TRANSMISSION / TRANSAXLE › COUNTER GEAR › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002985 M5S MANUAL TRANSMISSION / TRANSAXLE _0015109 COUNTER GEAR A

M5S MANUAL TRANSMISSION / TRANSAXLE  COUNTER GEAR  DISASSEMBLY  


PROCEDURE

Hide 33335 1.INSPECT 1ST GEAR THRUST CLEARANCE

C150512C02
0.427,0.125 0.656,0.313 0.229,0.188 10 *1 1.396,0.115 1.635,0.292 0.24,0.177 10 *2
*1 1st Gear
*2 2nd Gear


a.

Using a feeler gauge, measure the 1st gear thrust clearance.

Standard clearance:

0.10 to 0.56 mm (0.0039 to 0.0220 in.)


Maximum clearance:

0.56 mm (0.0220 in.)


If the clearance exceeds the maximum, disassemble and inspect the counter gear.


Hide 33332 2.INSPECT 2ND GEAR THRUST CLEARANCE

a.

Using a feeler gauge, measure the 2nd gear thrust clearance.

Standard clearance:

0.10 to 0.44 mm (0.0039 to 0.0173 in.)


Maximum clearance:

0.44 mm (0.0173 in.)


If the clearance exceeds the maximum, disassemble and inspect the counter gear.


Hide 33335 3.REMOVE 1ST GEAR

C150513

a.

Using 2 screwdrivers and a hammer, remove the snap ring.

NOTICE:

Use a piece of cloth to prevent the snap ring from flying off.



b.
C150514N02
1.302,1.26 0.875,0.833 true 0.542,0.729 0.865,0.906 0.323,0.177 10 SST

Use SST, remove the radial ball bearing, 1st gear thrust washer, 1st gear and No. 2 synchronizer ring.

SST
09950-00020  


c.
C150515

Remove the needle roller bearing.


d.
C150516N02
2.688,0.667 2.438,0.667 false 2.729,0.583 3.063,0.75 0.333,0.167 10 SST

Using SST, a vise and a snap expander, remove the snap ring, conical spring washer and 1st sub-gear.

SST
09350-32014  (09351-32070)


Hide 33332 4.REMOVE 2ND GEAR

C150517

a.

Using 2 screwdrivers and a hammer, remove the snap ring.

NOTICE:

Use a piece of cloth to prevent the snap ring from flying off.



b.
C150518N02
1.01,1.469 0.604,0.792 true 0.25,0.719 0.552,0.917 0.302,0.198 10 SST

Using SST and a press, remove the No. 1 synchronizer hub assembly, No. 3 synchronizer ring and 2nd gear.

SST
09950-00020  


c.
C150519

Remove the split type needle roller bearing.

NOTICE:

Do not widen the opening of the split type needle roller bearing 36 mm (1.42 in.) or more.



d.
C150520N02
2.5,0.521 2.25,0.521 false 2.542,0.438 2.917,0.625 0.375,0.188 10 SST

Using SST, a vise and a snap ring expander, remove the snap ring, conical spring washer and 2nd sub-gear.

SST
09350-32014  (09351-32070)


Hide 33321V 5.REMOVE OUTPUT SHAFT CENTER BEARING

C150521N02
1.219,1.031 0.75,0.563 true 0.417,0.479 0.729,0.646 0.313,0.167 10 SST

a.

Using SST and a press, remove the output shaft center bearing.

SST
09950-00020  


Hide 33360 6.REMOVE NO. 1 SYNCHRONIZER HUB ASSEMBLY

C150522

a.

Using a screwdriver, remove the 2 synchromesh shifting key springs.


b.

Remove the No. 1 hub sleeve and 3 synchromesh shifting keys.