Home › Drivetrain › M5S MANUAL TRANSMISSION / TRANSAXLE › COUNTER GEAR › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002985 M5S MANUAL TRANSMISSION / TRANSAXLE _0015109 COUNTER GEAR A

M5S MANUAL TRANSMISSION / TRANSAXLE  COUNTER GEAR  REASSEMBLY  


PROCEDURE

Hide 33360 1.INSTALL NO. 1 SYNCHRONIZER HUB ASSEMBLY

C150538

a.

Coat the No. 1 hub sleeve with manual transmission gear oil, and install it to the No. 1 clutch hub.


b.

Install the 3 synchromesh shifting keys and 2 synchromesh shifting key springs.


c.
C150539

Make sure that the openings of the right and left synchromesh shifting key springs are not aligned.


Hide 33321V 2.INSTALL OUTPUT SHAFT CENTER BEARING

C150540N02
2.052,0.76 1.813,0.76 false 2.104,0.677 2.427,0.854 0.323,0.177 10 SST

a.

Using SST and a press, install the output shaft center bearing.


Hide 33332 3.INSTALL 2ND GEAR

C150541C02
2.417,1.042 2.552,1.042 false 2.385,3.125 2.135,3.125 false 2.323,2.292 2.323,2.042 false 0.833,1.667 0.677,1.667 false 2.427,3.052 2.729,3.219 0.302,0.167 10 SST 2.583,0.958 2.771,1.146 0.188,0.188 10 *1 2.26,2.302 2.448,2.49 0.188,0.188 10 *3 0.49,1.594 0.688,1.771 0.198,0.177 10 *2
*1 2nd Gear
*2 Conical Spring Washer
*3 2nd Sub-gear


a.

Using SST, a vise and a snap ring expander, install the conical spring washer, 2nd sub-gear and a new snap ring to the 2nd gear.

SST
09350-32014  (09351-32070)


b.
C150519

Coat the split type needle roller bearing with manual transmission gear oil, and install it to the counter gear shaft.

NOTICE:

Do not widen the opening of the split type needle roller bearing 36 mm (1.42 in.) or more.



c.
C150542N02
2.125,0.594 1.885,0.594 false 2.167,0.51 2.521,0.698 0.354,0.188 10 SST

Using SST and a press, install the No. 1 synchronizer hub assembly, No. 3 synchronizer ring and 2nd gear.

SST
09608-06041  

NOTICE:

Paying attention to the proper position, fit the synchromesh shifting key into the groove of the synchronizer ring.



d.
C150543C02
2.677,1.063 2.521,1.531 true 2.448,1.563 2.615,1.74 0.167,0.177 10 *1
*1 Snap Ring


Select a new snap ring that allows the minimum amount of axial play.

Standard clearance:

0 mm (0 in.)


Maximum clearance:

0.16 mm (0.0063 in.)


Part No. Thickness mm (in.) Part No. Thickness mm (in.)
9004A-520534 2.06 (0.0811) 9004A-520578 1.90 (0.0748)
9004A-520545 2.02 (0.0795) 9004A-520589 1.86 (0.0732)
9004A-520556 1.98 (0.0780) 9004A-52060 1.82 (0.0717)
9004A-520567 1.94 (0.0764) 9004A-52061 2.10 (0.0827)


e.
C150544

Using a brass bar and a hammer, install the snap ring to the input shaft.


Hide 33335 4.INSTALL 1ST GEAR

C150545C02
2.583,3.135 2.344,3.135 false 0.99,1.656 0.75,1.656 false 2.563,1.042 2.313,1.042 false 2.323,2.302 2.208,2.302 2.208,2.302 1.896,1.99 false 2.635,3.052 3,3.25 0.365,0.198 10 SST 2.583,0.948 2.823,1.146 0.24,0.198 10 *1 0.542,1.563 0.75,1.729 0.208,0.167 10 *2 2.375,2.219 2.563,2.427 0.188,0.208 10 *3
*1 1st Gear
*2 Conical Spring Washer
*3 1st Sub-gear


a.

Using SST, a vise and a snap ring expander, install the conical spring washer, 1st sub-gear and a new snap ring to the 1st gear.

SST
09350-32014  (09351-32070)


b.
C150515

Coat the needle roller bearing with manual transmission gear oil, and install it to the counter gear shaft.


c.
C150546N02
2.156,0.604 1.906,0.604 false 2.198,0.542 2.542,0.74 0.344,0.198 10 SST

Using SST and press, install the radial ball bearing, 1st gear thrust washer, 1st gear and No. 2 synchronizer ring.

NOTICE:

Paying attention to the proper position, fit the synchromesh shifting key into the groove of the synchronizer ring.



d.
C150547C02
2.594,1.063 2.385,1.5 true 2.292,1.542 2.469,1.719 0.177,0.177 10 *1
*1 Snap Ring


Select a new snap ring that allows the minimum amount of axial play.

Standard clearance:

0 mm (0 in.)


Maximum clearance:

0.16 mm (0.0063 in.)


Part No. Thickness mm (in.) Part No. Thickness mm (in.)
9004A-520534 2.06 (0.0811) 9004A-520578 1.90 (0.0748)
9004A-520545 2.02 (0.0795) 9004A-520589 1.86 (0.0732)
9004A-520556 1.98 (0.0780) 9004A-52060 1.82 (0.0717)
9004A-520567 1.94 (0.0764) 9004A-52061 2.10 (0.0827)


e.
C150548

Using a brass bar and a hammer, install the snap ring to the counter gear shaft.