Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB
RM19Y0E _52 Drivetrain _002987 AXLE AND DIFFERENTIAL _0015116 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 43512 2.LOOSEN FRONT DISC

a.
C144774

Loosen the 4 bolts.


Hide 43514 3.REMOVE FRONT HUB GREASE CAP

C184745

a.

Using a screwdriver, remove the hub grease cap.

NOTICE:
·

Do not damage or deform the hub grease cap.

·

If the hub grease cap is damaged or deformed, replace it with a new one.




Hide 42601C 4.REMOVE FRONT AXLE HUB NUT

a.
C184746N01
1.948,1.052 0.875,1.885 true 0.521,1.865 1.177,2.177 0.656,0.313 10 SST

Using SST and a hammer, release the staked part of the front axle sub nut.

SST
09930-00010  


b.

Using a 36 mm socket wrench, remove the axle hub nut.


Hide 89543 5.SEPARATE FRONT SPEED SENSOR LH (w/ ABS)

a.
C144732

Remove the bolt and separate the front speed sensor bracket from the shock absorber.


b.
C248978

Disconnect the clamp from the shock absorber.


c.

Remove the bolt and speed sensor LH.

NOTICE:
·

Prevent foreign matter from contacting the sensor tip.

·

Remove the speed sensor without turning it from its original installation angle.




Hide 6.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY LH

C144731

a.

Remove the bolt and separate the flexible hose.


b.
C144769

Remove the 2 bolts and separate the disc brake caliper assembly LH from the steering knuckle.

NOTICE:

Hang the caliper using a piece of string or equivalent.



Hide 7.REMOVE FRONT AXLE HUB WITH FRONT DISC

a.
C246784N01
2.25,1.5 2.479,1.146 false 2.521,1.042 3.125,1.427 0.604,0.385 10 SST

Using SST, remove the axle hub with front disc.

SST
09520-00031  


Hide 45047 8.SEPARATE TIE ROD END SUB-ASSEMBLY LH

Hide 9.REMOVE FRONT AXLE ASSEMBLY

a.
C156084

Remove the 2 nuts, 2 bolts and front axle assembly.

NOTICE:

Do not damage the lower ball joint.


HINT:

Keep the bolt from rotating while turning the nut.



b.

Remove the clip and nut.


c.
C245934C02
0.76,1.542 0.615,1.542 0.615,1.542 0.615,1.938 false 0.74,1.604 0.615,1.604 false 2.135,1.406 1.99,1.406 1.99,1.406 1.99,1.948 true 2.135,1.552 1.99,1.552 true 0.49,1.948 1.01,2.177 0.521,0.229 10 SST 1.885,1.958 2.365,2.177 0.479,0.219 10 SST 2.917,1.24 3.365,1.646 0.448,0.406 10 *a
*a 1 mm (0.04 in.)


Install SST to the front lower suspension arm ball joint as shown in the illustration.

SST
09960-20010  (09961-02050, 09961-02050)

NOTICE:

Check that the clearance measurement between SST and the steering knuckle is 1 mm (0.04 in.).



d.

Using SST, remove the front lower suspension arm ball joint from the steering knuckle as shown in the illustration.

C245933C02
3.479,2.521 3.479,2.938 false 0.552,2.042 1.135,2.625 0.583,0.583 10 A 0.552,1.729 0.865,2.073 0.313,0.344 10 B 6.052,0.469 6.552,1.031 0.5,0.563 10 *c 4.333,2.104 4.854,2.5 0.521,0.396 10 *d 5.49,2.615 5.917,2.979 0.427,0.365 10 *a 5.51,2.958 6.01,3.375 0.5,0.417 10 *b 3.354,2.969 4.115,3.552 0.76,0.583 10 SST
*a Apply grease *b Apply grease
*c Place the wrench here *d Turn


SST
09960-20010  (09961-02050, 09961-02050)

NOTICE:

Apply grease to the threads and end of the SST bolt.


HINT:
·

Install SST so that A and B are parallel.

·

Be sure to place a wrench on the part indicated in the illustration.

·

Do not damage the front lower suspension arm ball joint dust cover.




Hide 47704 10.REMOVE FRONT DISC BRAKE DUST COVER SUB-ASSEMBLY LH

a.
C202598

Remove the disc brake dust cover LH by tapping the back side with a brass bar and hammer.


Hide 43502G 11.REMOVE FRONT AXLE HUB HOLE SNAP RING LH

a.

Using snap ring pliers, remove the front axle hub hole snap ring LH.


Hide 43212 12.REMOVE STEERING KNUCKLE LH

a.
C246771N01
2.667,1.073 2.667,1.469 false 2.552,1.49 3.229,1.969 0.677,0.479 10 SST

Using SST, and a press, remove the bearing from the steering knuckle LH.

SST
09950-60010  (09951-00630)
09223-56010  

NOTICE:
·

Check that the SST is positioned in the center of the bearing.

·

Remove the bearing slowly and carefully.




Hide 43512 13.REMOVE FRONT DISC

a.
C249328C01
1.688,1.073 0.938,1.406 true 0.698,1.344 1.208,1.708 0.51,0.365 10 *a
*a Matchmark


Put matchmarks on the axle hub and front disc.


b.

Remove the 4 bolts and front disc.


Hide 43502C 14.REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)

a.
C246772C01
1.344,0.198 1.448,0.76 false 0.292,0.24 0.885,0.688 0.594,0.448 10 *a 1.781,0.5 2.229,0.833 0.448,0.333 10 *b 1.052,0.042 1.688,0.427 0.635,0.385 10 SST
*a Turn
*b Hold


Using SST, remove the hub bearing inner race (outer side) from the axle hub sub-assembly LH.