Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE SHAFT
RM19Y0E _52 Drivetrain _002987 AXLE AND DIFFERENTIAL _0015118 REAR AXLE SHAFT A

AXLE AND DIFFERENTIAL  REAR AXLE SHAFT  REASSEMBLY  


PROCEDURE

Hide 42311C 1.INSTALL REAR AXLE SHAFT BEARING

a.

Clean the bearing retainer with non-residue solvent.


b.

Install the bearing retainer to the rear axle shaft.


c.

Apply MP grease to the outer surface of a new bearing outer race.


d.
C144885
0.698,0.531 0.958,0.667 false 0.531,1.469 0.958,1.365 true 0.365,0.427 0.865,0.719 0.5,0.292 10 SST 0.198,1.406 0.938,1.875 0.74,0.469 10 SST

Using SST and a press, press on the new bearing.

SST
09515-21010  
09608-32010  


Hide 42423 2.INSTALL REAR INNER AXLE BEARING RETAINER

a.

Heat a new inner retainer to approximately 150 °C (302 °F).

CAUTION:

Be sure to wear gloves because the inner retainer is extremely hot.



b.
C144886
0.469,0.594 0.75,0.677 true 0.365,1.656 0.802,1.563 true 0.49,2.823 0.76,2.865 false 0.365,3.938 0.792,3.844 true 0.177,0.5 0.771,0.948 0.594,0.448 10 SST 0.031,1.573 0.813,2.031 0.781,0.458 10 SST 0.135,2.74 0.573,2.917 0.438,0.177 10 SST 0.073,3.865 0.729,4.219 0.656,0.354 10 SST 0.052,0.042 0.563,0.417 0.51,0.375 10 *A 0.052,2.271 0.583,2.708 0.531,0.438 10 *B
*A w/o ABS
*B w/ ABS


Install the inner retainer in the direction shown in the illustration using SST and a press.

SST
09515-21010  
09608-32010  

NOTICE:

w/ ABS:

Install the inner retainer with the chamfer facing down.



Hide 89547D 3.INSTALL SKID CONTROL SENSOR ROTOR (w/ ABS)

C144887
0.688,0.427 0.844,0.552 true 0.438,1.583 0.875,1.531 true 0.344,0.323 1.063,0.656 0.719,0.333 10 SST 0.083,1.469 0.802,1.802 0.719,0.333 10 SST 2.854,1.083 3.292,1.469 0.438,0.385 10 (A)

a.

Install a new sensor rotor in the direction shown in the illustration using SST and a press.

SST
09631-32020  
09608-32010  

Distance (A):

6.2 to 7.2 mm (0.244 to 0.283 in.)



Hide 42611E 4.INSTALL REAR AXLE HUB BOLT

C144888
1.479,1.823 2.052,1.708 true 1.271,1.76 1.875,2.115 0.604,0.354 10 *1
*1 Plate Washer


a.

Mount the rear axle shaft in a soft vise.


b.

Pass 4 new axle hub bolts through the rear axle shaft and plate washer as shown in the illustration and install it by tightening the nut (M12 x 1.5 mm).

HINT:

A plate washer of 5 mm or thicker is preferable.