Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(for 3SZ-VE) › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002987 AXLE AND DIFFERENTIAL _0015122 REAR DIFFERENTIAL CARRIER ASSEMBLY(for 3SZ-VE) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for 3SZ-VE)  DISASSEMBLY  


PROCEDURE

Hide 41101 1.FIX REAR DIFFERENTIAL CARRIER ASSEMBLY

C151296

Hide 2.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C231133C01
2.198,0.104 2.583,0.479 0.385,0.375 10 *b 0.469,0.094 0.938,0.417 0.469,0.323 10 *a 2.25,1.833 2.865,2.177 0.615,0.344 10 *c
*a Vertical Runout
*b Lateral Runout
*c 30 mm (1.18 in.)


Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum runout
Runout Maximum
Vertical runout 0.10 mm (0.0039 in.)
Lateral runout 0.10 mm (0.0039 in.)

If the runout is greater than the maximum, replace the companion flange.



Hide 3.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C145169

Using a dial indicator, check the runout of the ring gear.

Maximum runout:

0.10 mm (0.0039 in.)


If the runout is greater than the maximum, replace the ring gear with a new one.



Hide 4.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C145168

Using a dial indicator, check the backlash of the ring gear.

Backlash:

0.08 to 0.13mm (0.0031 to 0.0052 in.)


If the backlash is not within the specification, adjust the side bearing preload or repair as necessary.

HINT:

Perform the measurements at 3 or more positions around the circumference of the ring gear.




Hide 5.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C003092

Using a torque wrench, measure the preload of the differential drive pinion.

Preload (at starting):
Bearing Standard
New bearing 0.57 to 0.96 N*m (5.8 to 9.8 kgf*cm, 5.0 to 8.5 in.*lbf)
Used bearing 0.49 to 0.78 N*m (5.0 to 8.0 kgf*cm, 4.5 to 7.0 in.*lbf)


If necessary, disassemble and inspect the differential.

HINT:

Make a note of the values for the below total preload inspection procedure.



Hide 6.INSPECT TOTAL PRELOAD

a.
C003092

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Total preload (at starting):

Drive pinion preload plus 0.20 to 0.39 N*m (2.0 to 4.0 kgf*cm, 1.8 to 3.5 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 7.REMOVE REAR DRIVE PINION NUT

a.
F044346N03
2.375,1.021 2.833,1.302 0.458,0.281 10 SST

Using SST and a hammer, loosen the staked part of the nut.

SST
09930-00010  


b.
C145171C01
1.938,0.719 2.177,0.469 false 1.875,2.885 2.177,2.74 2.177,2.74 1.948,3.031 true 0.115,2.208 0.563,2.583 0.448,0.375 10 *B 0.115,0.104 0.75,0.583 0.635,0.479 10 *A 2.229,0.365 2.792,0.708 0.563,0.344 10 SST 2.24,2.656 2.896,3.094 0.656,0.438 10 SST
*A for Manual Transmission
*B for Automatic Transmission


Using SST to hold the companion flange in place, remove the nut.

i.

for Manual Transmission:

SST
09330-87301  


ii.

for Automatic Transmission:

SST
09330-00021  
09950-30012  (09955-03030)



Hide 41204 8.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C111761C01
1.688,0.188 1.979,0.677 false 1.365,0.094 2,0.521 0.635,0.427 10 SST 2.802,0.594 3.177,0.958 0.375,0.365 10 *a 1.49,0.896 1.823,1.219 0.333,0.323 10 *b
*a Turn
*b Hold


Using SST, remove the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 41252 9.REMOVE REAR DIFFERENTIAL DUST DEFLECTOR

HINT:

Remove the dust deflector only when replacement is necessary due to damage or deformation.


a.
C120203N09
1.698,0.594 1.146,0.594 1.146,0.594 1.354,0.927 false 1.146,0.594 1.635,0.927 true 1.688,2.365 1.313,2.365 1.313,2.365 1.375,2.771 false 1.313,2.365 1.615,2.688 false 0.844,0.521 1.531,0.927 0.688,0.406 10 SST 0.99,2.302 1.552,2.76 0.563,0.458 10 SST

Using SST and a press, press out the dust deflector.

SST
09950-00020  
09950-70010  (09951-07150)
09950-60010  (09951-00430)

NOTICE:

Do not drop the companion flange.



Hide 41201C 10.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C158732C01
1.958,1.51 2.396,1.781 false 2.458,1.729 3.063,1.969 0.604,0.24 10 SST 0.979,1.625 1.396,1.958 0.417,0.333 10 *b 2.802,1.417 3.292,1.771 0.49,0.354 10 *a
*a Turn
*b Hold


Using SST, remove the oil seal from the differential carrier.

SST
09308-10010  


Hide 41201B 11.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C111764C01
0.688,0.188 1.073,0.615 false 0.417,0.927 0.896,1.24 0.479,0.313 10 *b 1.49,0.698 1.938,1.073 0.448,0.375 10 *a 0.354,0.083 1.01,0.396 0.656,0.313 10 SST
*a Turn
*b Hold


Using SST, remove the roller bearing (inner) from the drive pinion.

SST
09556-30010  


Hide 41201E 12.REMOVE REAR DIFFERENTIAL DRIVE PINION SPACER FRONT ADJUST SHIM

Hide 41231 13.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 41316 14.REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C145173

Remove the 2 bolts and 2 adjusting nut locks.


Hide 41311J 15.REMOVE REAR DIFFERENTIAL CASE

a.
C145174C01
1.792,1.333 1.375,1.906 1.375,1.906 1.792,1.469 true 1.177,1.917 1.604,2.177 0.427,0.26 10 *a
*a Matchmark


Place matchmarks on the bearing cap and differential carrier.


b.

Remove the 4 bolts and 2 differential bearing caps.


c.

Remove the 2 rear differential bearing adjusting nuts.


d.
C197099

Remove the rear differential case assembly from the differential carrier.


e.
C145175C01
0.865,1.646 1.302,2 0.438,0.354 10 *a 2.448,1.646 2.896,2.063 0.448,0.417 10 *b
*a RH
*b LH


Put indication marks of the right and left (back side, tooth surface side) on the adjusting nut and case bearing (outer race), or separate them clearly.


Hide 16.REMOVE DIFFERENTIAL DRIVE PINION

a.
C030540

Remove the drive pinion from the differential carrier.


Hide 41201A 17.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C145176N02
1.167,0.667 1.375,0.333 false 2.479,1.385 2.646,1.115 false 2.729,1.031 3.229,1.302 0.5,0.271 10 SST 1.406,0.26 2.021,0.656 0.615,0.396 10 SST

Using SST and a press, press out the roller bearing (inner) from the drive pinion.

SST
09950-00020  

NOTICE:

Do not drop the drive pinion.


HINT:

If the drive pinion or ring gear is damaged, replace them as a set.



Hide 41201B 18.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C097761

Using a brass bar and hammer, tap out the outer race from the carrier.

HINT:

If the bearing or outer race is damaged during removal, replace it.



Hide 41201A 19.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C231135

Using a brass bar and a hammer, remove the front tapered roller bearing (outer) from the carrier.

HINT:

If the bearing is damaged during removal, replace it.



Hide 41201D 20.REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

Hide 21.REMOVE DIFFERENTIAL RING GEAR

a.
C145177C01
2.125,1.438 2.917,1.719 2.917,1.719 2.208,1.583 true 2.99,1.646 3.427,1.979 0.438,0.333 10 *a
*a Matchmark


Place matchmarks on the ring gear and differential case.


b.

Remove the 10 bolts.


c.

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 22.INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

a.

Install the rear differential case bearing onto the differential case.


b.

Install the differential case onto the differential carrier.


c.

Install the 2 bearing caps onto the differential carrier with the 4 bolts.

Torque:
84 N*m (852 kgf*cm, 62 ft.*lbf)


d.
G020277

Using a dial indicator, measure the differential case runout.

Maximum runout:

0.05 mm (0.002 in.)



e.

Remove the differential case.


f.

Remove the rear differential case bearing.


Hide 41301A 23.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
F040345N04
0.427,0.25 0.844,0.25 false 0.844,0.25 0.844,0.781 false 0.104,0.198 0.625,0.542 0.521,0.344 10 SST

Using SST, remove the 2 bearings from the differential case.

SST
09950-60010  (09951-00410)
09950-40011  (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)

HINT:

Do not remove the case bearing unless replacing the differential case.



Hide 41311J 24.DISASSEMBLE REAR DIFFERENTIAL CASE

a.

Remove the following parts from the differential case.

C229928C01
1.688,0.448 1.427,0.448 false 1.885,0.771 1.427,0.771 false 5.427,0.854 5.135,0.854 false 5.427,1.229 5.021,1.229 false 5.427,1.563 5.156,1.563 false 5.427,0.5 5.021,0.5 false 1.75,1.125 1.427,1.125 false 2.333,1.281 2.333,0.948 false 3.271,1.354 3.115,1.354 false 3.271,0.979 2.896,0.979 false 3.271,0.625 2.938,0.625 false 5.427,0.208 5.167,0.208 false 1.229,0.375 1.573,0.635 0.344,0.26 10 *5 1.229,0.698 1.563,0.979 0.333,0.281 10 *4 1.229,1.063 1.594,1.354 0.365,0.292 10 *1 5.5,0.76 5.875,1.031 0.375,0.271 10 *3 5.49,1.146 6.01,1.458 0.521,0.313 10 *2 5.49,1.479 5.885,1.76 0.396,0.281 10 *1 5.49,0.417 5.854,0.729 0.365,0.313 10 *2 5.49,0.115 5.906,0.51 0.417,0.396 10 *1 2.271,1.302 2.74,1.677 0.469,0.375 10 *2 3.344,1.292 3.833,1.677 0.49,0.385 10 *5 3.344,0.906 3.74,1.229 0.396,0.323 10 *4 3.344,0.563 3.917,0.927 0.573,0.365 10 *1
*1 Pinion gear *2 Pinion shaft
*3 Spider *4 Side gear
*5 Side gear thrust washer - -