Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.11–2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC / Data List.


f.

According to the display on the tester, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Air Bleeding Support Air bleed support SUPPORT or NOT SUP SUPPORT : Supported
NOT SUP : Not supported
-
Parking Brake Switch Parking brake switch ON or OFF ON : Parking brake applied
OFF : Parking brake released
ON is also displayed when either condition is met:
·

The brake fluid level is low (the brake fluid level warning switch is on).

·

The vacuum in the brake booster decreases (the vacuum warning switch is on).


Stop Light Switch Stop light switch ON or OFF ON : Brake pedal depressed
OFF : Brake pedal released
-
ABS Motor Relay ABS motor relay ON or OFF ON : Motor relay on
OFF : Motor relay off
-
Solenoid Relay Solenoid relay ON or OFF ON : Solenoid relay on
OFF : Solenoid relay off
-
ECU Code ECU product number code Min .: 0 Max. : 15 - -
Test Mode Test mode Normal or Test Normal : Normal mode
Test : Test mode
-
RL Wheel ABS control Rear wheel LH ABS operation Before or Operate Before : No ABS operation
Operate : During ABS operation
-
RR Wheel ABS control Rear wheel RH ABS operation Before or Operate Before : No ABS operation
Operate : During ABS operation
-
FL Wheel ABS control Front wheel LH ABS operation Before or Operate Before : No ABS operation
Operate : During ABS operation
-
FR Wheel ABS control Front wheel RH ABS operation Before or Operate Before : No ABS operation
Operate : During ABS operation
-
ABS Solenoid (SRLR) Rear wheel LH release solenoid ON or OFF ON : Operates
OFF : Does not operate
-
ABS Solenoid (SRLH) Rear wheel RH hold solenoid ON or OFF ON : Operates
OFF : Does not operate
-
ABS Solenoid (SRRR) Rear wheel RH release solenoid ON or OFF ON : Operates
OFF : Does not operate
-
ABS Solenoid (SRRH) Rear wheel RH hold solenoid ON or OFF ON : Operates
OFF : Does not operate
-
ABS Solenoid (SFLR) Front wheel LH release solenoid ON or OFF ON : Operates
OFF : Does not operate
-
ABS Solenoid (SFLH) Front wheel LH hold solenoid ON or OFF ON : Operates
OFF : Does not operate
-
ABS Solenoid (SFRR) Front wheel RH release solenoid ON or OFF ON : Operates
OFF : Does not operate
-
ABS Solenoid (SFRH) Front wheel RH hold solenoid ON or OFF ON : Operates
OFF : Does not operate
-
FR Wheel Speed Front speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front speed sensor LH reading Min. : 0 km/h (0 mph)
Max. : 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
RR Wheel Speed Rear speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear speed sensor LH reading Min. : 0 km/h (0 mph)
Max. : 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
Vehicle Speed Maximum wheel speed sensor reading Min. : 0 Max. : 326.4 Actual vehicle speed Speed indicated on speedometer
ECU IG Power Voltage ECU power supply voltage too Low, Normal or too High Normal -


ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC / Active Test.


f.

According to the display on the tester, perform the Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Control Range Inspection Item Diagnostic Note
Brake Warning Light ON / OFF BRAKE warning light Observe the combination meter.
ABS Warning Light ON / OFF ABS warning light Observe the combination meter.
2nd Sys. Air Bleeding ON / OFF Secondary solenoid Pump motor drive (used when removing air inside ABS actuator)
Actuator drive(RL) ON / OFF Rear left pressure reduction and retention solenoid Pump motor drive
Actuator drive(RR) ON / OFF Rear right pressure reduction and retention solenoid Pump motor drive
Actuator drive(FL) ON / OFF Front left pressure reduction and retention solenoid Pump motor drive
Actuator drive(FR) ON / OFF Front right pressure reduction and retention solenoid Pump motor drive