Home › Brake › BRAKE (REAR) › REAR BRAKE
RM19Y0E _54 Brake _002995 BRAKE (REAR) _0015155 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REASSEMBLY  


PROCEDURE

Hide 47547R 1.TEMPORARILY TIGHTEN REAR DRUM BRAKE BLEEDER PLUG

Hide 04474 2.INSTALL REAR WHEEL CYLINDER KIT

a.
C152624C02
0.281,1.781 0.281,1.531 false 0.656,1.677 0.656,1.375 false 1.042,1.573 1.042,1.271 false 2.052,1.323 2.052,0.917 false 2.396,1.198 2.396,0.833 false 2.74,1.073 2.74,0.729 false 3.094,0.958 3.094,0.667 false 0.198,1.813 0.375,1.969 0.177,0.156 10 *1 0.583,1.708 0.771,1.896 0.188,0.188 10 *2 0.958,1.604 1.135,1.771 0.177,0.167 10 *3 1.979,1.354 2.156,1.5 0.177,0.146 10 *4 2.323,1.229 2.531,1.427 0.208,0.198 10 *3 2.677,1.104 2.906,1.292 0.229,0.188 10 *2 3.021,0.99 3.219,1.156 0.198,0.167 10 *1
*1 Wheel cylinder boot
*2 Piston
*3 Wheel cylinder cup
*4 Compression spring
V100135

Lithium soap base glycol grease


Apply lithium soap base glycol grease to 2 new wheel cylinder boots and the 2 pistons.


b.

Install 2 new wheel cylinder cups onto each piston.


c.

Install the compression spring and 2 pistons onto the wheel brake cylinder.


d.

Install the wheel cylinder boots onto the wheel brake cylinder.


Hide 47570 3.INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY

a.
C152625

Install the rear wheel brake cylinder assembly with the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 7 ft.*lbf)


b.

Using union nut wrench, install the brake tube.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 47601 4.INSTALL REAR BRAKE PARKING BRAKE SHOE LEVER SUB-ASSEMBLY

a.
C062256

Using needle-nose pliers, install the rear brake parking brake shoe lever sub-assembly with a new C-washer.


Hide 5.INSTALL REAR BRAKE SHOE

a.
C246395C02
3.052,2.052 3.292,2.052 false
V100144

High Temperature Grease


Apply high temperature grease to the surface of the backing plate which is in contact with the shoe.


b.
C152620

Using needle-nose pliers, install the parking brake cable onto the parking brake shoe lever.


c.
C246381

Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

SST
09718-00011  


Hide 47062 6.INSTALL PARKING BRAKE SHOE STRUT SET

a.
C246396C02
3.073,2.073 3.313,2.073 false
V100144

High Temperature Grease


Apply high temperature grease to the adjusting bolt.


b.

Install the parking brake shoe strut set to the rear brake shoe.


Hide 7.INSTALL FRONT BRAKE SHOE

a.

Install the cylinder support spring to the front brake shoe and the rear brake shoe.

NOTICE:

Check that the parking brake shoe strut set is installed securely.



b.
C246397C02
3.063,2.073 3.323,2.073 false
V100136

High Temperature Grease


Apply high temperature grease to the parts shown in the illustration.


c.

Using needle-nose pliers, install the shoe return spring onto the front brake shoe and rear brake shoe.


d.
C246380

Using pliers, install the front brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

SST
09718-00011  


Hide 47643A 8.INSTALL REAR BRAKE AUTOMATIC ADJUST LEVER

a.

Install the automatic adjust lever to the rear brake shoe.


b.

Using a screwdriver, install the automatic adjust lever support spring to the front brake shoe and the automatic adjust lever.


Hide 9. CHECK REAR DRUM BRAKE INSTALLATION

a.

Check that each part is installed properly.

C152629C02
1.771,0.083 2.292,0.448 0.521,0.365 10 *a 5.24,0.083 6.01,0.573 0.771,0.49 10 *b
*a for LH Side *b for RH Side
V100135

Front of the vehicle - -



b.
C152631

Measure the brake drum inner diameter and the diameter of the brake shoes. Check that the difference between the diameters is equal to the specified shoe clearance.

Shoe clearance:

0.6 mm (0.024 in.)


NOTICE:

There should be no oil or grease adhering to the friction surfaces of the shoe lining or the drum.