Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.11–2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM U

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TERMINALS OF ECU  


CHECK POWER STEERING ECU ASSEMBLY


C228557C02
2.208,2.281 2.604,2.521 0.396,0.24 4,2.281 4.396,2.521 0.396,0.24 3.063,2.281 3.458,2.521 0.396,0.24 4.667,2.281 5.063,2.521 0.396,0.24 0.125,0.063 0.375,0.26 0.25,0.198 10 *a 2.281,2.323 2.552,2.479 0.271,0.156 10 E26 4.073,2.323 4.344,2.479 0.271,0.156 10 E27 3.177,2.323 3.344,2.479 0.167,0.156 10 z1 4.792,2.323 4.958,2.479 0.167,0.156 10 z2
*a Component with harness connected
(Power Steering ECU Assembly)
- -


a.

Measure the voltage and resistance according to the value(s) in the table below.

NOTICE:
·

Check if the power steering ECU assembly connectors are securely connected by pulling on them from the backside.

·

If the EPS warning light is illuminated due to a malfunction, the fail-safe function may cause the voltage of the power steering ECU's terminals to become 0 V.



Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E26-1 (IGP) - Body ground B - Body ground EPS fuse Always 11 to 14 V
E26-2 (GND) - Body ground W-B - Body ground Body ground Always Below 1 Ω
E27-2 (SIO) - E26-2 (GND) LG-B - B Intelligent tester or Techstream
·

Ignition switch ON

·

Connect the intelligent tester or Techstream to the DLC3


Pulse generation
(See waveform 1)
E27-5 (SPD) - E26-2 (GND) W-L - W-B Vehicle speed signal Vehicle being driven Pulse generation
(See waveform 2)
E27-6 (IG) - Body ground R - Body ground ECU-IG No. 1 fuse Ignition switch ON 11 to 14 V
E27-8 (IDUP) - E26-2 (GND) P - W-B ECM Ignition switch ON
Steering wheel not turned
11 to 14 V
E27-9 (W) - E26-2 (GND) B-R - W-B EPS warning light output signal Ignition switch off → ON For approximately 2 seconds 11 to 14 V → Below 1 V
E27-11 (EPST) - Body ground L - Body ground EPST terminal Ignition switch ON 11 to 14 V
E27-12 (REV) - E26-2 (GND) B-Y - W-B Engine speed signal Engine running Pulse generation
(See waveform 3)
z2-5 (TRQ1) - Body ground - Torque sensor 1 input signal Engine running, steering wheel not turned (without load) 2.2 to 2.8 V
Engine running, steering wheel turned to right with vehicle stopped 2.2 to 4.85 V
Engine running, steering wheel turned to left with vehicle stopped 0.15 to 2.8 V
z2-6 (TRQV) - Body ground - Torque sensor power source Ignition switch ON 4.5 to 5.5 V
z2-7 (TRQ2) - Body ground - Torque sensor 2 input signal Engine running, steering wheel not turned (without load) 2.2 to 2.8 V
Engine running, steering wheel turned to right with vehicle stopped 0.15 to 2.8 V
Engine running, steering wheel turned to left with vehicle stopped 2.2 to 4.85 V
z2-8 (TRQG) - Body ground - Torque sensor ground Always Below 1 Ω
z1-1 (M1) - E26-2 (GND) - Power steering motor
·

Ignition switch ON

·

Steering wheel turned to left


Below 1 V
·

Ignition switch ON

·

Steering wheel turned to right


11 to 14 V
z1-2 (M2) - E26-2 (GND) - Power steering motor
·

Ignition switch ON

·

Steering wheel turned to left


11 to 14 V
·

Ignition switch ON

·

Steering wheel turned to right


Below 1 V


b.
C189665N01
2.665,0.033 3.253,0.195 0.587,0.162 10 5 V/DIV . 2.807,1.172 3.138,1.338 0.331,0.166 10 GND 1.075,1.973 1.791,2.11 0.715,0.138 10 1 ms./DIV .

Waveform 1

Terminal SIO - GND
Tool setting 5 V/DIV ., 1 ms./DIV .
Vehicle condition Connect the intelligent tester or Techstream to the DLC3


c.
A287266N01
2.677,0.052 3.344,0.24 0.667,0.188 10 5 V/DIV . 2.833,1.229 3.292,1.427 0.458,0.198 10 GND 1.188,1.99 2.031,2.177 0.844,0.188 10 20 ms./DIV .

Waveform 2

Terminal SPD - GND
Tool setting 5 V/DIV ., 20 ms./DIV .
Vehicle condition Driving wheel rotated slowly


d.
A287266N02
2.708,0.052 3.292,0.25 0.583,0.198 10 5 V/DIV . 2.854,1.24 3.313,1.438 0.458,0.198 10 GND 1.219,2 2.083,2.177 0.865,0.177 10 10 ms./DIV .

Waveform 3

Terminal REV - GND
Tool setting 5 V/DIV ., 10 ms./DIV .
Vehicle condition Idling