DATA LIST
Using the intelligent tester or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the intelligent tester or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the tester or Techstream on.
Enter the following menus: Chassis / EMPS / Data List.
According to the display on tester, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Torque Sensor 1 Output | Torque sensor 1 output value | Min.: 0 V
Max.: 5 V |
(*a) 2.2 to 2.8 V
(*b) 2.2 to 4.85 V (*c) 0.15 to 2.8 V |
(*a) Steering wheel not turned (without load)
(*b) Steering wheel turned to right with vehicle stopped (*c) Steering wheel turned to left with vehicle stopped |
| Meter Vehicle Velocity | Vehicle speed from meter | Min.: 0 km/h (0 mph)
Max.: 300 km/h (186.4 mph) |
(*a) 0 km/h (0 mph)
(*b) No significant fluctuation |
(*a) Vehicle stopped
(*b) Vehicle driven at constant speed |
| Torque Sensor 2 Output | Torque sensor 2 output value | Min.: 0 V
Max.: 5 V |
(*a) 2.2 to 2.8 V
(*b) 0.15 to 2.8 V (*c) 2.2 to 4.85 V |
(*a) Steering wheel not turned (without load)
(*b) Steering wheel turned to right with vehicle stopped (*c) Steering wheel turned to left with vehicle stopped |
| Engine Revolution | Engine speed | Min.: 0 rpm
Max.: 12800 rpm |
Engine is running at a constant speed | No significant fluctuation |
| Motor Actual Current | Current to motor | Min.: -327.67 A
Max.: 327.68 A |
Value changes in proportion to steering effort | Power steering is in operation |
| Command Value Current | Requested current to motor | Min.: -327.67 A
Max.: 327.68 A |
Value changes in proportion to steering effort | Power steering is in operation |
| Steering Angle Velocity | Steering angle speed | Min: -32768 deg/s
Max: 32767 deg/s |
Value changes in proportion to steering effort | The engine is running and steering wheel is being turned |
| Thermistor Temperature | ECU substrate temperature | Min.: -40°C (-40°F)
Max.: 150 °C (302°F) |
-40 to 150 °C (-40 to 302°F) | Ignition switch ON |
| PIG Power Supply | Power source voltage to activate motor | Min.: 0 V
Max.: 21.1531 V |
11 to 14 V | Power steering is in operation |
| IG Power Supply | ECU power source voltage | Min.: 0 V
Max.: 21.1531 V |
11 to 14 V | Ignition switch ON |
| TRQ1 Zero Point Value | Zero point value of torque sensor 1 | Min.: 0 V
Max.: 5 V |
2.2 to 2.8 V | Steering wheel not turned (without load) |
| TRQ2 Zero Point Value | Zero point value of torque sensor 2 | Min.: 0 V
Max.: 5 V |
2.2 to 2.8 V | Steering wheel not turned (without load) |
| Steering Wheel Torque | Steering wheel torque | Min.: -7.00 Nm
Max.: 7.00 Nm |
Value changes in proportion to steering effort | The engine is running and the steering wheel is being turned. |
| Motor Terminal Volt(+) | Motor terminal M1 voltage | Min.: 0 V
Max.: 25.5 V |
(*a) 6 to 8 V
(*b) 11 to 14 V |
(*a) Steering wheel turned to right
(*b) Steering wheel turned to left |
| Motor Terminal Volt(-) | Motor terminal M2 voltage | Min.: 0 V
Max.: 25.5 V |
(*a) 11 to 14 V
(*b) 6 to 8 V |
(*a) Steering wheel turned to right
(*b) Steering wheel turned to left |
| Torque Sensor 3 Output | Torque value for assist control | Min.: 0 V
Max.: 5 V |
(*a) 2.2 to 2.8 V
(*b) 0.15 to 2.8 V (*c) 2.2 to 4.85 V |
(*a) Steering wheel not turned (without load)
(*b) Steering wheel turned to right with vehicle stopped (*c) Steering wheel turned to left with vehicle stopped |
| Motor Overheat Record | Continuous overheat prevention control record | Unrec/Rec | Unrec or Rec | - |
| Motor Lo Power Record | PIG power source voltage drop record | Unrec/Rec | Unrec or Rec | - |
| Battery Voltage Lo Record | Battery voltage reduction history | Min: 0 times
Max: 65535 times |
0 times | - |
| Battery Voltage | Battery voltage | Min: 0 V
Max: 25 V |
11 to 14 V | - |
| TRQ Sensor Power Supply | Torque sensor power source voltage | Min.: 0 V
Max.: 21.1531 V |
5 to 13 V | Power steering is in operation |
| Motor Voltage | Motor Power Supply Voltage | Min.: 0 V
Max.: 39.5 V |
11 to 14 V | Ignition switch ON |
| System Power Supply | System power source voltage | Min.: 0 V
Max.: 21.1531 V |
9.5 to 16 V | Power steering is in operation |
| The Number of DTCs | Number of detected DTCs when freeze frame data stored | Min.: 0
Max.: 255 |
- | - |