Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.11–2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


NOTICE:
·

It is difficult to show the specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.

·

Turn the ignition switch to ON and park the vehicle on level ground. Check the freeze frame data by using the intelligent tester or Techstream.



a.

Turn the ignition switch off.


b.

Connect the intelligent tester or Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester or Techstream on.


e.

Check the freeze frame data by following the prompts on the intelligent tester or Techstream display.

HINT:

Refer to the intelligent tester or Techstream operator's manual for further details.


Chassis > EMPS
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Torque Sensor 1 Output Torque sensor 1 output value Min.: 0 V
Max.: 5 V
(*a) 2.2 to 2.8 V
(*b) 2.2 to 4.85 V
(*c) 0.15 to 2.8 V
(*a) Steering wheel not turned (without load)
(*b) Steering wheel turned to right with vehicle stopped
(*c) Steering wheel turned to left with vehicle stopped
Meter Vehicle Velocity Vehicle speed from meter Min.: 0 km/h (0 mph)
Max.: 300 km/h (186.4 mph)
(*a) 0 km/h (0 mph)
(*b) No significant fluctuation
(*a) Vehicle stopped
(*b) Vehicle driven at constant speed
Torque Sensor 2 Output Torque sensor 2 output value Min.: 0 V
Max.: 5 V
(*a) 2.2 to 2.8 V
(*b) 0.15 to 2.8 V
(*c) 2.2 to 4.85 V
(*a) Steering wheel not turned (without load)
(*b) Steering wheel turned to right with vehicle stopped
(*c) Steering wheel turned to left with vehicle stopped
Engine Revolution Engine speed Min.: 0 rpm
Max.: 12800 rpm
Engine is running at a constant speed No significant fluctuation
Motor Actual Current Current to motor Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort Power steering is in operation
Command Value Current Requested current to motor Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort Power steering is in operation
Thermistor Temperature ECU substrate temperature Min.: -40°C (-40°F)
Max.: 150 °C (302°F)
-40 to 150 °C (-40 to 302°F) Ignition switch ON
PIG Power Supply Power source voltage to activate motor Min.: 0 V
Max.: 21.1531 V
11 to 14 V Power steering is in operation
IG Power Supply ECU power source voltage Min.: 0 V
Max.: 21.1531 V
11 to 14 V Ignition switch ON
TRQ1 Zero Point Value Zero point value of torque sensor 1 Min.: 0 V
Max.: 5 V
2.2 to 2.8 V Steering wheel not turned (without load)
TRQ2 Zero Point Value Zero point value of torque sensor 2 Min.: 0 V
Max.: 5 V
2.2 to 2.8 V Steering wheel not turned (without load)
Motor Terminal Volt(+) Motor terminal M1 voltage Min.: 0 V
Max.: 25.5 V
(*a) 6 to 8 V
(*b) 11 to 14 V
(*a) Steering wheel turned to right
(*b) Steering wheel turned to left
Motor Terminal Volt(-) Motor terminal M2 voltage Min.: 0 V
Max.: 25.5 V
(*a) 11 to 14 V
(*b) 6 to 8 V
(*a) Steering wheel turned to right
(*b) Steering wheel turned to left