Home › Steering › STEERING COLUMN › STEERING WHEEL › 2011.11–2015.08
RM19Y0E _55 Steering _002998 STEERING COLUMN _0015164 STEERING WHEEL G

STEERING COLUMN  STEERING WHEEL  INSPECTION  


PROCEDURE

Hide 45102 1.INSPECT STEERING WHEEL SUB-ASSEMBLY (w/ Steering Pad Switch)

a.

Measure the resistance according to the value(s) in the table below.

C245563
1.958,3.167 1.958,2.885 1.958,2.885 2.115,2.885 true 2.344,3.25 2.646,3.25 true 2.208,3.583 2.281,3.865 true 4.604,2.688 4.823,2.604 true 1.802,3.458 1.344,3.458 true 1.854,3.875 1.854,4.146 true 3.844,1.302 3.615,1.302 true 4.135,1.281 4.135,0.698 4.135,0.698 4.063,0.698 true 4.271,1.271 4.271,0.781 4.271,0.781 4.698,0.781 true 4.396,1.281 4.771,1.104 true 2.125,2.813 2.656,3.229 0.531,0.417 10 *1 2.667,3.177 3.156,3.625 0.49,0.448 10 *3 2.208,3.885 2.667,4.365 0.458,0.479 10 *4 1.76,4.156 2.313,4.604 0.552,0.448 10 *5 4.823,2.5 5.385,3 0.563,0.5 10 *6 3.76,0.635 4.385,1.01 0.625,0.375 10 AU1 4.708,0.708 5.365,1.146 0.656,0.438 10 AU2 4.802,1.042 5.469,1.573 0.667,0.531 10 EAU 3.385,1.219 3.875,1.573 0.49,0.354 10 HO 3.417,0.844 3.917,1.24 0.5,0.396 10 *a 1.167,3.375 1.667,3.885 0.5,0.51 10 *2
*1 Volume+ Switch *2 Volume- Switch
*3 Seek+ Switch *4 Seek- Switch
*5 MODE Switch *6 Terminal B
*a Component without harness connector
(Steering Wheel Sub-assembly (Steering Pad Switch Assembly))
- -


Standard Resistance
Tester Connection Switch Condition Specified Condition
1 (HO) - Terminal B Always Below 2.5 Ω
3 (AU1) - 5 (EAU) Volume+ Switch pushed 95 to 105 kΩ
Volume- Switch pushed 3105 to 3115 Ω
Seek+ Switch pushed Below 2.5 Ω
Seek- Switch pushed 324 to 334 Ω
4 (AU2) - 5 (EAU) Volume+ Switch pushed 95 to 105 kΩ
MODE Switch pushed Below 2.5 Ω

If the result is not as specified, replace the steering wheel sub-assembly.


b.

Check the illumination.

i.

Connect the battery positive (+) lead to terminal 2 (IL+2) and the negative (-) lead to terminal 5 (EAU) of the steering pad switch assembly connector.


ii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


If the result is not as specified, replace the steering wheel sub-assembly.