Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › 2011.11–2015.08
RM19Y0E _56 Audio / Visual / Telematics _003000 AUDIO / VIDEO _0015166 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  USB Device or "iPod" cannot Charge  


WIRING DIAGRAM

E232726E02
4.833,2.99 6.365,3.646 1.531,0.656 10 STEREO JACK ADAPTER ASSEMBLY 4.844,2.792 5.156,2.958 0.313,0.167 10 E52 4.896,0.771 5.208,0.938 0.313,0.167 10 UPI 4.667,0.667 4.823,0.833 0.156,0.167 10 1 4.875,2.25 5.344,2.417 0.469,0.167 10 UJSG 4.667,2.156 4.823,2.323 0.156,0.167 10 4 2.125,0.792 2.479,0.958 0.354,0.167 10 UPO 2.573,0.667 2.729,0.833 0.156,0.167 10 1 2.052,2.26 2.521,2.427 0.469,0.167 10 UESG 2.563,2.156 2.719,2.323 0.156,0.167 10 4 1.021,2.958 2.615,3.615 1.594,0.656 10 STEREO COMPONENT TUNER ASSEMBLY 1.021,2.792 1.469,2.958 0.448,0.167 10 E53

CAUTION / NOTICE / HINT

HINT:

USB device or "iPod" may not be able to charge on vehicle when its battery is particularly depleted.


PROCEDURE

1.REPLACE USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the stereo jack adapter assembly.


b.

Turn the ignition switch off.

HINT:

When this malfunction occurs, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.



c.

Turn the ignition switch to ACC.


d.

Connect a known good USB device or "iPod" to the stereo jack adapter assembly.

OK:

USB device or "iPod" charges.


Result:
Proceed to
OK
NG




OK

USB DEVICE OR "iPod" WAS DEFECTIVE

NG

2.INSPECT STEREO COMPONENT TUNER ASSEMBLY
2.INSPECT STEREO COMPONENT TUNER ASSEMBLY
a.
E234124C03
1.5,0.302 1.948,0.583 0.448,0.281 1.385,1.177 0.979,1.177 true 2.51,1.198 2.094,1.198 true 0.156,0.042 0.385,0.229 0.229,0.188 10 *a 1.594,0.365 1.885,0.521 0.292,0.156 10 E52 0.698,1.104 0.99,1.26 0.292,0.156 10 UPI 2.552,1.125 2.958,1.323 0.406,0.198 10 UJSG
*a Front view of wire harness connector
(to Stereo Jack Adapter Assembly)


Disconnect the E52 stereo jack adapter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E52-1 (UPI) - E52-4 (UJSG) Ignition switch ACC 5 V


Result:
Proceed to
OK
NG




OK

NG

3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT TUNER - STEREO JACK ADAPTER)
3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT TUNER - STEREO JACK ADAPTER)
a.

Disconnect the E53 stereo component tuner assembly connector.]


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E52-1 (UPI) - E53-1 (UPO) Always Below 1 Ω
E52-4 (UJSG) - E53-4 (UESG) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E52-1 (UPI) - Body ground Always 10 kΩ or higher
E52-4 (UJSG) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR