Home › Power Source / Network › K3-VE BATTERY / CHARGING › GENERATOR › 2011.11–2015.08
RM19Y0E _57 Power Source / Network _003002 K3-VE BATTERY / CHARGING _0015178 GENERATOR A

K3-VE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27411 1.REMOVE GENERATOR PULLEY

a.
A193553C10
2.844,0.708 2.531,1.198 true 3.083,0.583 3.125,1.531 true 1.208,1.5 1.531,1.885 0.323,0.385 10 *b 1.833,1.896 2.292,2.177 0.458,0.281 10 *a 2.198,1.229 2.917,1.667 0.719,0.438 10 SST1-B 2.781,1.573 3.406,2.042 0.625,0.469 10 SST1-A
*a Hold
*b Turn


Clamp the generator housing stay in a vise tightly.


b.

Hold SST 1-A with a torque wrench, and tighten SST 1-B clockwise with the specified torque.

SST
09820-63011  (09820-06010, 09820-06021)

Item Part No.
SST 1-A and B 09820-06010
SST 2 09820-06021

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Check that SST is securely fitted onto the generator rotor shaft.



c.
A193554N13
2.531,0.49 2.667,0.906 false 2.146,0.365 2.917,0.854 0.771,0.49 10 SST2

Insert SST2, and engage SST2 to the generator pulley nut.


d.
A193555C06
2.51,0.656 1.885,0.927 true 3.01,0.917 3.063,1.448 true 1.469,0.875 2.135,1.354 0.667,0.479 10 SST2 2.74,1.49 3.344,2.052 0.604,0.563 10 SST1-A 1.292,2.719 1.698,3.094 0.406,0.375 10 *a 2.125,2.917 2.552,3.323 0.427,0.406 10 *b
*a Hold
*b Turn


Insert SST 1-A and B into SST 2, and attach the pulley nut to SST 2.

NOTICE:

To prevent damage to the rotor shaft, do not loosen the generator pulley nut by more than one half turn.



e.

Remove SST2 from the generator assembly.


f.
A193556C09
2.854,0.771 2.51,1.167 true 3.052,0.635 3.031,1.448 true 2.167,1.188 2.927,1.583 0.76,0.396 10 SST1-B 2.75,1.49 3.354,1.958 0.604,0.469 10 SST1-A 2.177,1.5 2.615,1.917 0.438,0.417 10 *a 1.531,1.417 1.906,1.813 0.375,0.396 10 *b
*a Hold
*b Turn


Remove the generator assembly from SST 2.


g.

Remove the generator pulley nut and generator pulley.


h.

Remove the generator assembly from a vise.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.
A162309

Remove the 3 nuts and generator rear end cover.


Hide 27387 3.REMOVE TERMINAL INSULATOR

a.
A162310

Remove the terminal insulator.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A162311

Remove the 2 screws and generator brush holder assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A162312

Remove the 4 bolts.


b.
A115868C04
0.771,0.26 1.333,0.604 false 2.635,0.458 3.115,0.875 0.479,0.417 10 *b 0.26,0.646 0.708,1.042 0.448,0.396 10 *a 0.375,0.167 1.01,0.573 0.635,0.406 10 SST
*a Hold
*b Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


Hide 27330 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.

Remove the washer.


b.

Remove the rotor from the generator rear end cover.


Hide 27310B 7.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A118440

Check that the generator drive end frame bearing is not rough or worn.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A118441

Remove the 4 screws and bearing retainer.


b.
A118442N04
1.24,0.938 0.479,0.813 0.479,0.813 1.208,1.313 true 0.094,0.74 0.781,1.167 0.688,0.427 10 SST

Using SST and a hammer, tap out the generator drive end frame bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)