Home › Power Source / Network › 3SZ-VE BATTERY / CHARGING › GENERATOR › 2011.11–2015.08
RM19Y0E _57 Power Source / Network _003003 3SZ-VE BATTERY / CHARGING _0015180 GENERATOR A

3SZ-VE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27411 1.REMOVE GENERATOR PULLEY

a.
A193553C08
2.844,0.708 2.531,1.198 true 3.083,0.583 3.073,1.521 true 1.24,1.448 1.625,1.781 0.385,0.333 10 *b 1.833,1.865 2.25,2.146 0.417,0.281 10 *a 2.198,1.229 2.958,1.635 0.76,0.406 10 SST1-B 2.781,1.573 3.375,2.052 0.594,0.479 10 SST1-A
*a Hold
*b Turn


Clamp the generator housing stay in a vise tightly.


b.

Hold SST 1-A with a torque wrench, and tighten SST 1-B clockwise with the specified torque.

SST
09820-63011  (09820-06010, 09820-06021)

Item Part No.
SST 1-A and B 09820-06010
SST 2 09820-06021

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Check that SST is securely fitted onto the generator rotor shaft.



c.
A193554N11
2.531,0.49 2.667,0.906 false 2.115,0.365 2.781,0.844 0.667,0.479 10 SST2

Insert SST2, and engage SST2 to the generator pulley nut.


d.
A193555C05
2.51,0.656 1.885,0.927 true 3.021,0.917 3.073,1.448 true 1.469,0.854 2.156,1.333 0.688,0.479 10 SST2 2.74,1.49 3.323,1.99 0.583,0.5 10 SST1-A 1.281,2.74 1.708,3.135 0.427,0.396 10 *a 2.125,2.917 2.531,3.302 0.406,0.385 10 *b
*a Hold
*b Turn


To loosen the generator pulley nut, turn SST1-A in the direction shown in the illustration.

NOTICE:

To prevent damage to the rotor shaft, do not loosen the generator pulley nut by more than one half turn.



e.

Remove SST2 from the generator assembly.


f.
A193556C07
2.854,0.771 2.479,1.208 true 3.052,0.635 3.031,1.438 true 2.229,1.24 2.969,1.656 0.74,0.417 10 SST1-B 2.75,1.49 3.365,1.917 0.615,0.427 10 SST1-A 2.177,1.51 2.521,1.813 0.344,0.302 10 *a 1.521,1.406 1.896,1.792 0.375,0.385 10 *b
*a Hold
*b Turn


Hold SST1-A, Turn SST1-B, and remove SST1-A and SST1-B in the direction shown in the illustration.


g.

Remove the generator pulley nut and generator pulley.


h.

Remove the generator assembly from a vise.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.
A162309

Remove the 3 nuts and generator rear end cover.


Hide 27387 3.REMOVE TERMINAL INSULATOR

a.
A162310

Remove the terminal insulator.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A162311

Remove the 2 screws and generator brush holder assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A162312

Remove the 4 bolts.


b.
A115868C03
0.771,0.26 1.344,0.594 false 2.635,0.458 3.125,0.896 0.49,0.438 10 *b 0.396,0.583 0.885,0.969 0.49,0.385 10 *a 0.448,0.156 0.958,0.573 0.51,0.417 10 SST
*a Hold
*b Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


Hide 27330 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.

Remove the washer.


b.

Remove the rotor from the generator rear end cover.


Hide 27310B 7.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A118440

Check that the generator drive end frame bearing is not rough or worn.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A118441

Remove the 4 screws and bearing retainer.


b.
A118442N03
1.24,0.938 0.479,0.813 0.479,0.813 1.208,1.313 true 0.146,0.729 0.833,1.208 0.688,0.479 10 SST

Using SST and a hammer, tap out the generator drive end frame bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)