Home › Power Source / Network › 3SZ-VE BATTERY / CHARGING › GENERATOR › 2011.11–2015.08
RM19Y0E _57 Power Source / Network _003003 3SZ-VE BATTERY / CHARGING _0015180 GENERATOR A

3SZ-VE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A118448N04
1.188,0.885 0.51,0.24 0.51,0.24 1.063,1.313 true 0.135,0.156 0.833,0.635 0.698,0.479 10 SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60010  (09951-00430)
09950-70010  (09951-07100)


b.
A118449C03
0.979,1.813 1.49,1.406 true 2.344,0.323 1.75,0.896 true 0.75,1.802 1.24,2.156 0.49,0.354 10 *1 2.375,0.208 2.948,0.667 0.573,0.458 10 *1
*1 Claw


Align the claws of the bearing retainer with the grooves inside the generator drive end frame.


c.

Install the bearing retainer with the 4 screws.


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Install the generator drive end frame on the generator rotor assembly.

NOTICE:

Do not drop the generator rotor assembly.



b.

Install the generator rotor assembly and new washer.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A118450C02
2.083,0.229 1.833,0.594 false 2.125,0.083 2.635,0.49 0.51,0.406 10 *1
*1 Deep Socket Wrench(21mm)


Using a deep socket wrench (21mm) and press, slowly press in the generator coil assembly.


b.
A162312

Install the generator coil assembly with the 4 through bolts.

Torque:
5.8 N*m (59 kgf*cm, 51 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A118452C03
1.26,0.531 1,0.844 true 1.281,0.438 1.719,0.833 0.438,0.396 10 *1
*1 Pin


While pushing the 2 brushes to the inside of the generator brush holder assembly, insert a φ1.0 mm (0.039 in.) pin into the brush holder hole.


b.
A118453C03
1.74,0.885 1.74,1.125 true 1.656,1.156 2.063,1.615 0.406,0.458 10 *1
*1 Pin


Install the generator brush holder assembly with the 2 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


c.

Pull out the pin from the generator brush holder assembly.


Hide 27387 5.INSTALL TERMINAL INSULATOR

a.
A162310

Install the terminal insulator.


Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.
A162309

Install the generator rear end cover with the 3 nuts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27411 7.INSTALL GENERATOR PULLEY

a.
A193553C09
2.844,0.708 2.531,1.198 true 3.083,0.583 3.083,1.531 true 1.229,1.458 1.542,1.823 0.313,0.365 10 *b 1.833,1.865 2.177,2.146 0.344,0.281 10 *a 2.198,1.229 2.875,1.729 0.677,0.5 10 SST1-B 2.781,1.573 3.354,2.052 0.573,0.479 10 SST1-A
*a Hold
*b Turn


Clamp the generator housing stay in a vise tightly.


b.

Install the generator pulley onto the generator rotor shaft by tightening the generator pulley nut by hand.


c.

Hold SST1-A with a torque wrench, and tighten SST1-B clockwise to the specified torque.

SST
09820-63011  (09820-06010, 09820-06021)

Item Part No.
SST 1-A and B 09820-06010
SST 2 09820-06021

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

Check that SST is securely fitted onto the generator rotor shaft.



d.
A193554N12
2.531,0.49 2.667,0.906 false 2.125,0.365 2.76,0.844 0.635,0.479 10 SST2

Insert SST2, and engage SST2 to the pulley nut.


e.
A248835C05
2.917,0.875 1.802,0.531 true 2.5,0.438 1.5,0.135 true 1.24,0.438 1.969,0.906 0.729,0.469 10 SST1-A 1.094,0.052 1.969,0.49 0.875,0.438 10 SST2 1.188,2.438 1.573,2.823 0.385,0.385 10 *a 1.917,3.094 2.281,3.406 0.365,0.313 10 *b
*a Hold
*b Turn


Tighten the generator pulley nut by turning SST1-A in the direction shown in the illustration.

Torque:
133 N*m (1350 kgf*cm, 98 ft.*lbf)

HINT:

Hold the adjustable wrench against the vise and tighten the nut securely.



f.

Remove SST 2 from the generator assembly.


g.
A193556C08
2.854,0.771 2.448,1.188 true 3.052,0.635 3.052,1.385 true 2.208,1.219 3.052,1.656 0.844,0.438 10 SST1-B 2.771,1.448 3.333,2.063 0.563,0.615 10 SST1-A 2.146,1.479 2.563,1.875 0.417,0.396 10 *a 1.521,1.406 1.958,1.792 0.438,0.385 10 *b
*a Hold
*b Turn


Hold SST1-A, Turn SST1-B, and remove SST1-A and SST1-B from the generator assembly.


h.

Turn the generator pulley, and check that the generator pulley moves smoothly.


i.

Remove the generator assembly from a vise.