Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003005 DOOR LOCK _0015187 WIRELESS DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the door control transmitter. Then, the door control receiver sends lock/unlock signals to all door lock motors.

WIRING DIAGRAM

B297556E02
5.656,0.802 7.052,1.365 1.396,0.563 10 from Ignition or Starter Switch Assembly 5.656,0.385 6.76,0.906 1.104,0.521 10 from IG Relay 3.052,0.958 4.083,1.375 1.031,0.417 10 IG1/BACK 3.271,0.531 3.865,0.969 0.594,0.438 10 D/L 4.333,3.156 4.833,3.594 0.5,0.438 10 Lock 4.333,2.594 4.948,3.021 0.615,0.427 10 Unlock 3.5,8.458 5.896,8.865 2.396,0.406 10 BACK DOOR LOCK ASSEMBLY 3.51,8.302 3.979,8.635 0.469,0.333 10 L4 5.708,7.656 7.063,8.479 1.354,0.823 10 REAR DOOR LOCK ASSEMBLY RH 5.708,7.5 6.125,7.823 0.417,0.323 10 H4 3.698,7.542 4.01,7.927 0.313,0.385 10 2 3.698,8 3.979,8.313 0.281,0.313 10 1 3.875,8 4.417,8.292 0.542,0.292 10 U/L+ 3.875,7.552 4.49,7.844 0.615,0.292 10 LOK+ 3.281,6.417 5.781,6.979 2.5,0.563 10 REAR DOOR LOCK ASSEMBLY LH 3.281,6.25 3.708,6.563 0.427,0.313 10 I4 5.563,5.688 7.083,6.229 1.521,0.542 10 FRONT DOOR LOCK ASSEMBLY RH*1/LH*2 5.563,5.521 6.156,5.865 0.594,0.344 10 F7*1 3.073,4.333 6.323,4.906 3.25,0.573 10 FRONT DOOR LOCK ASSEMBLY LH*1/RH*2 3.49,4.156 4.021,4.49 0.531,0.333 10 F5*2 3.073,4.156 3.781,4.625 0.708,0.469 10 G7*1 0.427,8.188 2.667,8.719 2.24,0.531 10 DOOR CONTROL RECEIVER 0.427,8.031 1.052,8.323 0.625,0.292 10 E62 2,7.469 2.417,7.771 0.417,0.302 10 15 2.031,3.771 2.385,4.073 0.354,0.302 10 1 2.031,3.375 2.542,3.865 0.51,0.49 10 2 1.99,2.99 2.417,3.406 0.427,0.417 10 18 2.031,2.583 2.375,2.958 0.344,0.375 10 6 2.031,0.323 2.427,0.688 0.396,0.365 10 25 1.802,0.406 2.26,0.833 0.458,0.427 10 B 2.031,0.708 2.438,1.052 0.406,0.344 10 12 1.802,7.563 2.115,7.906 0.313,0.344 10 E 1.604,3.865 2.333,4.396 0.729,0.531 10 ULM 1.615,3.469 2.177,3.906 0.563,0.438 10 LKM 1.646,3.073 2.188,3.5 0.542,0.427 10 LKS 1.615,2.667 2.375,3.104 0.76,0.438 10 UKS 1.75,0.813 2.208,1.208 0.458,0.396 10 IG 3.521,2.844 4.198,3.375 0.677,0.531 10 3*1 3.521,2.99 4.042,3.344 0.521,0.354 10 6*2 3.521,2.438 4.083,2.823 0.563,0.385 10 1*1 3.521,2.583 4,3.042 0.479,0.458 10 2*2 3.698,5.479 4.042,5.823 0.344,0.344 10 2 3.698,5.927 4.135,6.313 0.438,0.385 10 1 5.604,6.667 5.958,7.031 0.354,0.365 10 2 5.604,7.115 5.917,7.469 0.313,0.354 10 1 5.781,7.115 6.417,7.49 0.635,0.375 10 U/L+ 5.781,6.656 6.375,6.979 0.594,0.323 10 LOK+ 5.604,4.667 6,5.052 0.396,0.385 10 2 5.604,5.104 5.854,5.427 0.25,0.323 10 1 3.646,3.375 3.99,3.76 0.344,0.385 10 5 3.646,3.781 4,4.167 0.354,0.385 10 4 3.875,5.927 4.375,6.271 0.5,0.344 10 U/L+ 3.875,5.479 4.49,5.917 0.615,0.438 10 LOK+ 3.833,2.99 4.563,3.385 0.729,0.396 10 LKSW 3.833,2.583 4.365,2.979 0.531,0.396 10 U/L+ 3.833,3.781 4.427,4.177 0.594,0.396 10 U/L+ 3.833,3.375 4.604,3.844 0.771,0.469 10 LOK+ 5.781,5.115 6.469,5.51 0.688,0.396 10 U/L+ 5.781,4.667 6.521,5.052 0.74,0.385 10 LOK+ 5.042,2.802 5.427,3.156 0.385,0.354 10 1*2 4.854,2.781 5.156,3.146 0.302,0.365 10 E 4.594,1.365 4.948,1.646 0.354,0.281 10 2 3.802,1.365 4.104,1.677 0.302,0.313 10 1 3.198,1.844 5.438,2.375 2.24,0.531 10 STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY 3.208,1.688 3.698,2.063 0.49,0.375 10 E57 4.865,1.594 5.75,1.938 0.885,0.344 10 HAZARD 5.854,1.438 6.938,2.021 1.083,0.583 10 from IG1 Fuse 2,1.365 2.458,1.698 0.458,0.333 10 23 1.49,1.458 2.146,1.823 0.656,0.365 10 KYSW 0.958,8.479 2.052,8.844 1.094,0.365 10 *2 : for RHD 0.052,8.49 1.188,8.865 1.135,0.375 10 *1 : for LHD 5.948,5.521 6.542,5.865 0.594,0.344 10 G5*2 5.042,2.667 5.427,3.021 0.385,0.354 10 2*1

PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Each door locks and unlocks normally.


Result:
Proceed to
OK
NG




OK

2.CHECK KEY REMINDER WARNING SYSTEM

NG

2.CHECK KEY REMINDER WARNING SYSTEM
a.

Check that the key reminder warning buzzer operates normally.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK

OK:

Key reminder warning buzzer operates normally.


Result:
Proceed to
OK
NG




OK

3.CHECK DOOR CONTROL TRANSMITTER

NG

3.CHECK DOOR CONTROL TRANSMITTER
a.

Check whether the wireless door lock control functions operate normally with another registered transmitter.

OK:

Wireless door lock control functions operate normally.


Result:
Proceed to
OK
NG




OK

4.INSPECT TRANSMITTER BATTERY

NG

5.CHECK WAVE ENVIRONMENT
4.INSPECT TRANSMITTER BATTERY
B297553C01
1.615,0.583 1.938,0.396 false 1.948,0.281 2.365,0.646 0.417,0.365 10 *1
*1 Wire


a.

Remove the battery from the door control transmitter that does not operate.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(for Key Ring Type)>REPLACEMENT


b.

Attach a lead wire (0.6 mm (0.0236 in.) or less in diameter including wire sheath) with tape or equivalent to the negative terminal.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between the terminals or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.



c.

Carefully extend the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

NOTICE:

When replacing the transmitter battery, before starting work, remove any static electricity that has built up by touching, for example, the vehicle to prevent the door control transmitter from being damaged.



d.
B297554C01
1.271,0.521 1.656,0.333 false 1.667,0.198 2.146,0.594 0.479,0.396 10 *a
*a GND


Measure the voltage according to the value(s) in the table below.

HINT:
·

Measure the transmitter battery voltage while pressing the lock or unlock switch on the transmitter.

·

Perform the measurement when the door control transmitter is at room temperature.



Standard Voltage:
Tester Connection Condition Specified Condition
Battery positive (+) - Battery negative (-) Ignition switch off, all doors closed and lock or unlock switch pushed 2.2 to 3.2 V


Result:
Proceed to
OK
NG




OK

REPLACE DOOR CONTROL TRANSMITTER

NG

5.CHECK WAVE ENVIRONMENT
a.

Move the door control transmitter in the vicinity of the door control receiver.

HINT:

Refer to Parts Location for the location of the door control receiver.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>PARTS LOCATION



b.

Press and hold either the lock or unlock transmitter switch for 1 second and check that the doors lock or unlock accordingly.

OK:

Wireless door lock control functions operate normally.


HINT:
·

Check if electrical noise is the cause by moving the door control transmitter closer to the door control receiver. Moving it closer will decrease the effects of electrical noise.

·

If the operation check can be performed normally, there is a high probability that electrical noise or a decrease in output from the door control transmitter is the cause of the malfunction. There is a high probability that electrical noise is the cause if the problem occurs only in a certain location or only during a certain time of day. Also, custom components may be causing electrical noise. If custom components are installed in the vehicle, remove them and perform the operation check again.



Result:
Proceed to
OK
NG




OK

END (AFFECTED BY WAVE INTERFERENCE)

NG

6.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
B297555C04
1.49,0.052 1.979,0.344 0.49,0.292 2.469,1.094 2.24,1.844 true 0.948,1.396 0.698,1.844 true 2.656,1.396 2.906,1.844 true 0.615,1.854 0.938,2.073 0.323,0.219 10 E 2.125,1.854 2.49,2.115 0.365,0.26 10 IG 2.875,1.854 3.125,2.083 0.25,0.229 10 B 1.604,0.115 2.125,0.438 0.521,0.323 10 E62 0.24,0.229 0.583,0.521 0.344,0.292 10 *a
*a Front view of wire harness connector
(to Door Control Receiver)


a.

Disconnect the E62 door control receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E62-15 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E62-12 (IG) - Body ground Ignition switch ON 11 to 14 V
E62-25 (B) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR