Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015195 THEFT DETERRENT SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  TERMINALS OF ECU  


CHECK DOOR CONTROL RECEIVER


a.

Disconnect the E62 door control receiver connector.

B288728
3.469,0.154 3.866,0.392 0.397,0.238 3.545,0.201 3.84,0.357 0.296,0.157 10 E62


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E62-12 (IG) - Body ground P-B - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E62-25 (B) - Body ground B - Body ground*1
R - Body ground*2
Battery power supply Always 11 to 14 V
E62-15 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
E62-4 (CTY) - Body ground W - Body ground Door courtesy switch input All doors are closed 10 kΩ or higher
Any door is open*3 Below 1 Ω
Driver side or front passenger side door is open*4 Below 1 Ω
E62-14 (RMLP) - Body ground W-L - Body ground Interior light input Map light or No. 2 room light switch in DOOR position 11 to 14 V
E62-19 (FSW) - Body ground L-R - Body ground Engine hood courtesy switch input Engine hood fully closed 10 kΩ or higher
Engine hood fully open Below 1 Ω
E62-23 (KYSW) - Body ground W-R - Body ground Unlock warning switch input No key in ignition key cylinder Below 1 V
Key inserted into ignition key cylinder 11 to 14 V
E62-6 (UKS) - Body ground L - Body ground
·

Front door inside handle assembly LH (front door lock control knob LH) input*1

·

Front door inside handle assembly RH (front door lock control knob RH) input*2

·

Driver side door key-linked unlock input


·

Front door inside handle assembly LH (front door lock control knob LH) unlocked*1

·

Front door inside handle assembly RH (front door lock control knob RH) unlocked*2

·

Driver side door key cylinder in unlock position


Below 1 Ω
·

Front door inside handle assembly LH (front door lock control knob LH) locked*1

·

Front door inside handle assembly RH (front door lock control knob RH) locked*2

·

Driver side door key cylinder in neutral position


10 kΩ or higher
E62-18 (LKS) - Body ground B - Body ground*1
V - Body ground*2
·

Front door inside handle assembly LH (front door lock control knob LH) input*1

·

Front door inside handle assembly RH (front door lock control knob RH) input*2

·

Driver side door key-linked lock input


·

Front door inside handle assembly LH (front door lock control knob LH) locked*1

·

Front door inside handle assembly RH (front door lock control knob RH) locked*2

·

Driver side door key cylinder in lock position


Below 1 Ω
·

Front door inside handle assembly LH (front door lock control knob LH) unlocked*1

·

Front door inside handle assembly RH (front door lock control knob RH) unlocked*2

·

Driver side door key cylinder in neutral position


10 kΩ or higher

*1 : for LHD

*2 : for RHD

*3: w/ Rear Door Courtesy Switch

*4: w/o Rear Door Courtesy Switch


If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the E62 door control receiver connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E62-1 (ULM) - E62-15 (E) P - W-B Door lock motor unlock drive output
·

Front door inside handle assembly LH (front door lock control knob LH) locked*1

·

Front door inside handle assembly RH (front door lock control knob RH) locked*2

·

Driver side door key cylinder in neutral position


Below 1 V
·

Front door inside handle assembly LH (front door lock control knob LH) unlocked*1

·

Front door inside handle assembly RH (front door lock control knob RH) unlocked*2

·

Driver side door key cylinder in unlock position


11 to 14 V → Below 1 V
E62-2 (LKM) - E62-15 (E) G - W-B Door lock motor lock drive output
·

Front door inside handle assembly LH (front door lock control knob LH) locked*1

·

Front door inside handle assembly RH (front door lock control knob RH) locked*2

·

Driver side door key cylinder in lock position


Below 1 V
·

Front door inside handle assembly LH (front door lock control knob LH) locked*1

·

Front door inside handle assembly RH (front door lock control knob RH) locked*2

·

Driver side door key cylinder in lock position


11 to 14 V → Below 1 V
E62-3 (IND) - E62-15 (E) R-G - W-B Security indicator light signal Security indicator light illuminates during alarm sounding state 11 to 14 V
E62-14 (RMLP) - E62-15 (E) W-L - W-B Interior light illumination signal Disarmed state 11 to 14 V
Alarm sounding state when map light or No. 2 room light switch in DOOR position Below 1 V
E62-16 (HRN) - E62-15 (E)*3 V - W-B Vehicle horns (low pitched and high pitched) signal Armed state 11 to 14 V
Horns sound during alarm sounding state Pulse generation (Below 1 V ← → 11 to 14 V)
E62-17 (CHR) - E62-15 (E) R - W-B Hazard warning light signal Disarmed state 11 to 14 V
Hazard warning lights blink during alarm sounding state Below 1 V

*1 : for LHD

*2 : for RHD

*3: w/o Theft Warning ECU Assembly


If the result is not as specified, the door control receiver may have a malfunction.




CHECK THEFT WARNING ECU ASSEMBLY


B298509
3.479,0.083 3.875,0.323 0.396,0.24 3.573,0.125 4.083,0.458 0.51,0.333 10 J12

a.

Disconnect the J12 theft warning ECU assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J12-3 (+B) - Body ground R - Body ground Battery power supply Always 11 to 14 V
J12-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the J12 theft warning ECU assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J12-2 (RIN) - J12-1 (GND) LG-R - W-B Communication signal input from door control receiver Ignition switch ON Pulse generation (Below 1 V ← → 11 to 14 V)
J12-4 (SSIG) - J12-5 (SGND) LG-B - W-B Communication signal output to intrusion sensor Disarmed state 3 V
Arming preparation state or armed state Pulse generation (Below 1 V ← → 3 V)
J12-7 (ROUT) - J12-1 (GND) G-W - W-B Communication signal output to door control receiver Ignition switch ON Pulse generation (Below 1 V ← → 11 to 14 V)
J12-8 (REV) - J12-1 (GND) R-Y - W-B Engine speed signal input from ECM Engine idling Pulse generation (See waveform 1)
J12-9 (RSIG) - J12-5 (SGND) V - W-B Communication signal input from intrusion sensor Disarmed state 1.5 V
Arming preparation state or armed state Pulse generation (Below 1 V ← → 1.47 to 1.53 V)
J12-10 (SPW) - J12-5 (SGND) L - W-B Intrusion sensor power supply Disarmed state Below 1 V
Arming preparation state or armed state 3 V

*1 : for LHD

*2 : for RHD


If the result is not as specified, the door control receiver may have a malfunction.



e.
B298653N01
2.948,1.302 3.417,1.781 0.469,0.479 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) J12-8 (REV) - J12-1 (GND)
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine idling

HINT:

The wavelength becomes shorter as the engine speed increases.