Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015195 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit provides power for door control receiver and theft warning ECU assembly* operation.

*: w/ Theft Warning ECU assembly


WIRING DIAGRAM

B298510E02
4.396,2.24 7.083,2.667 2.688,0.427 10 THEFT WARNING ECU ASSEMBLY* 4.396,2.073 5.052,2.417 0.656,0.344 10 J12 4.542,1.031 6.781,1.677 2.24,0.646 10 DOOR CONTROL RECEIVER 4.542,0.885 5.031,1.188 0.49,0.302 10 E62 2.323,0.427 2.854,0.813 0.531,0.385 10 D/L 0.563,0.26 1.844,0.802 1.281,0.542 10 from IG1 Fuse 4.99,0.458 5.396,0.76 0.406,0.302 10 15 4.99,0.177 5.49,0.563 0.5,0.385 10 25 5.229,0.552 5.573,0.896 0.344,0.344 10 E 5.229,0.271 5.635,0.604 0.406,0.333 10 B 5.052,1.698 5.406,2.031 0.354,0.333 10 1 5.063,1.427 5.344,1.74 0.281,0.313 10 3 5.229,1.781 5.729,2.135 0.5,0.354 10 GND 5.229,1.5 5.573,1.76 0.344,0.26 10 +B 3.625,0.583 3.906,0.896 0.281,0.313 10 * 0.083,2.344 2.646,2.792 2.563,0.448 10 *: w/ Theft Warning ECU assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - DOOR CONTROL RECEIVER AND BODY GROUND)
a.

Disconnect the E62 door control receiver connector.


b.
B297555C03
1.49,0.052 1.979,0.344 0.49,0.292 0.948,1.396 0.698,1.844 true 2.656,1.396 2.906,1.844 true 0.615,1.854 1.104,2.135 0.49,0.281 10 E 2.875,1.854 3.219,2.125 0.344,0.271 10 B 1.604,0.115 2.135,0.448 0.531,0.333 10 E62
*a Front view of wire harness connector
(to Door Control Receiver)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E62-25 (B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
E62-15 (E) - Body ground Always Below 1 Ω


Result:
Result Proceed to
OK (w/ Theft Warning ECU) A
OK (w/o Theft Warning ECU) B
NG C




A

2.CHECK HARNESS AND CONNECTOR (BATTERY - THEFT WARNING ECU ASSEMBKY AND BODY GROUND)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BATTERY - THEFT WARNING ECU ASSEMBKY AND BODY GROUND)
a.

Disconnect the J12 theft warning ECU assembly connector.


b.
B298942C01
1.5,0.125 1.99,0.417 0.49,0.292 1.26,1.333 1.063,1.948 true 1.729,1.354 1.927,1.969 true 1.625,0.188 2.135,0.51 0.51,0.323 10 J12 0.917,1.979 1.438,2.177 0.521,0.198 10 GND 1.865,1.979 2.333,2.177 0.469,0.198 10 +B 0.229,0.177 0.604,0.563 0.375,0.385 10 *a
*a Front view of wire harness connector
(to Theft Warning ECU Assembly)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J12-3 (+B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
J12-1 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR