Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015195 THEFT DETERRENT SYSTEM D

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  SYSTEM DESCRIPTION  


OUTLINE OF THEFT DETERRENT SYSTEM


w/o Theft Warning ECU Assembly
·

The theft deterrent system can be set by locking the doors using the transmitter.

·

The alarm function will be activated when someone attempts to forcibly unlock any of the doors or open any of the doors, engine hood, and back door while the system is in the armed state.

·

In the alarm sounding state, the system flashes the hazard warning lights. At the same time, the system sounds the vehicle horn to deter break-in and theft as well as to warn people around the vehicle.

·

The alarm can be cancelled by unlocking the doors using the transmitter.

·

The theft deterrent system has the active arming mode. There are 3 states; a disarmed state, an armed state, and an alarm sounding state.


w/ Theft Warning ECU Assembly
·

The theft deterrent system can be set by locking the doors using the transmitter.

·

The alarm function will be activated when someone attempts to forcibly unlock any of the doors or open any of the doors, engine hood, and back door while the system is in the armed state.

·

In the alarm sounding state, the system flashes the hazard warning lights. At the same time, the system sounds the vehicle horn and security buzzer to deter break-in and theft as well as to warn people around the vehicle.

·

The alarm can be cancelled by unlocking the doors using the transmitter.

·

The theft deterrent system has the active arming mode. There are 4 states; a disarmed state, an arming preparation state, an armed state, and an alarm sounding state.


a.

Disarmed state:

·

The alarm function is not operating.

·

The theft deterrent system is not operating.



b.

Arming preparation state (w/ Theft Warning ECU Assembly):

·

The time until the system goes into the armed state.

·

The theft deterrent system is not operating.



c.

Armed state:

·

The theft deterrent system is operating.



d.

Alarm sounding state:

·

The alarm function is operating.


Alarm time:

Approximately 30 seconds.


Alarm Method and Time (w/o Theft Warning ECU Assembly)
Alarm Method Hazard Warning Lights Flashing
Map Light Assembly
No. 2 Room Light Assembly
Illuminate
Vehicle Horn Sounding
(approximately 0.5 second intervals)
Alarm Time Approximately 30 seconds

Alarm Method and Time (w/ Theft Warning ECU Assembly)
Alarm Method Hazard Warning Lights Flashing
Map Light Assembly
No. 2 Room Light Assembly
Illuminate
Security Buzzer Sounding
(approximately 0.5 second intervals)
Alarm Time Approximately 30 seconds



FUNCTION OF MAIN COMPONENTS


Component Function
Security indicator light Informs driver of theft deterrent system status.
Security buzzer*1 Sounds when attempted break-in or theft is detected.
Low pitched horn*2
High pitched horn*2
Sound when attempted break-in or theft is detected.
Hazard warning lights Flash when attempted break-in or theft is detected.
Map light assembly
No. 2 Room light assembly
Illuminates when attempted break-in or theft is detected.
Intrusion sensor*1 Sends signal to theft warning ECU assembly to sound alarm when detecting intrusion.
Door courtesy light switch Detects door status (open or closed).
Engine hood switch Detects engine hood status (open or closed).
Back door courtesy switch Detects back door status (open or closed).
Ignition or starter switch assembly Detects ignition switch status (off or on).
Unlock warning switch Detects ignition key status (insert or not).
Door control receiver Receives wireless door lock/unlock signal.

*1: w/ Theft Warning ECU Assembly

*2: w/o Theft Warning ECU Assembly



ACTIVE ARMING MODE


HINT:

Active arming mode starts the alarm control immediately after the doors are locked.


a.

Active arming mode:

This system operates as described in the diagram below when one of the items for each condition is met.

w/o Theft Warning ECU Assembly
B298502E02
3.125,0.635 4.5,1.25 1.375,0.615 10 Disarmed State 3.229,1.938 4.563,2.406 1.333,0.469 10 Armed State 2.938,3.25 4.656,3.729 1.719,0.479 10 Alarm Sounding State 0.844,2.958 2.156,3.531 1.313,0.573 10 Condition [3] 0.844,1.667 2.115,2.26 1.271,0.594 10 Condition [3] 2.906,2.583 4.031,3.104 1.125,0.521 10 Condition [4] 4.542,2.573 5.813,3.115 1.271,0.542 10 Condition [2] 3.74,1.281 4.896,1.76 1.156,0.479 10 Condition [1]

Condition Item
Condition [1] In the disarmed state, when the key is not inserted into the ignition key cylinder, the system state changes if the following condition is met.
·

With all doors, the engine hood and back door closed, all doors are locked by wireless operation.


HINT:

If the doors are unlocked again by wireless operation, the doors will be locked after 30 seconds due to the automatic lock function and the system will change to the armed state.


Condition [2]
·

Any door is unlocked without wireless operation

·

The engine hood is opened when the engine hood is closed.

·

Any door is opened when all doors are closed.*1

·

Driver side or front passenger side door is opened when all doors are closed.*2

·

The back door is opened when the back door is closed.


HINT:

If any passenger door or the back door is opened, horns sound 5 seconds after the door is opened. The hazard warning lights, interior lights and security indicator illuminate or blink immediately when the door is opened. Horns sound immediately if the engine hood is opened.


Condition [3]
·

All doors are unlocked by wireless operation.

·

The key is inserted in the ignition key cylinder.

·

The ignition switch to ON.


Condition [4] All doors are locked by wireless operation.
HINT:

After approximately 30 seconds, interior lights transfer to delay control. And if all doors and engine hood are closed for 1 second, door lock signal is output and system returns to armed state.




*1: w/ Rear Door Courtesy Switch

*2: w/o Rear Door Courtesy Switch


w/ Theft Warning ECU Assembly
B298503
3.135,0.646 4.563,1.271 1.427,0.625 10 Disarmed State 2.833,1.865 4.781,2.479 1.948,0.615 10 Arming Preparation State 3.229,3.104 4.344,3.604 1.115,0.5 10 Armed State 2.927,4.333 4.698,4.813 1.771,0.479 10 Alarm Sounding State 2.865,3.719 4.135,4.219 1.271,0.5 10 Condition [6] 2.854,1.26 4.156,1.813 1.302,0.552 10 Condition [3] 3.688,2.5 5.01,3.042 1.323,0.542 10 Condition [2] 4.49,1.26 5.708,1.823 1.219,0.563 10 Condition [1] 4.49,3.719 5.844,4.313 1.354,0.594 10 Condition [4] 0.875,4.063 2.073,4.531 1.198,0.469 10 Condition [5] 0.875,2.823 2.115,3.323 1.24,0.5 10 Condition [5]

Condition Item
Condition [1] In the disarmed state, when the key is not inserted into the ignition key cylinder, the system state changes if the following condition is met.
·

With all doors, engine hood and back door closed, lock all doors by wireless operation.


HINT:

If the doors are unlocked again by wireless operation, the doors will be locked after 40 seconds due to the automatic lock function and the system will change to the armed state.


Condition [2]
·

Allow approximately 30 seconds to elapse.


Condition [3]
·

All doors are unlocked by wireless operation.

·

Any door is opened.

·

The engine hood is opened.

·

The back door is opened.

·

The battery is reconnected.

·

The ignition switch is turned from off to ON.


Condition [4]
·

Any door is opened when all doors are closed.

·

The engine hood is opened when the engine hood is closed.

·

The back door is opened when the back door is closed.

·

Cut wire harness of theft deterrent system circuit.

·

Turn ignition switch from off to on when key is not inserted into ignition key cylinder.

·

Intrusion sensor detects movement within vehicle when intrusion sensor is activated.

·

Interrupt the battery.


Condition [5]
·

All doors are unlocked by wireless operation.

·

Turn the ignition switch to ON and run engine approximately 2 seconds.


Condition [6] After approximately 30 sec. (10 times), alarm stops and system returns to armed state.




SECURITY INDICATOR LIGHT OUTPUT


a.

The door control receiver outputs a signal to light up the security indicator, according to the state of the theft deterrent system. However, some of the actual lighting conditions of the security indicator are different from the output signals of the door control receiver.

Output
State of Theft Deterrent System Security Indicator light
Output Signal from Main Body ECU (Multiplex Network Body ECU) Actual Lighting Condition
Disarmed state (1), (2) OFF OFF
OFF (Immobiliser system unset)*1
BLINKING (Immobiliser system set)*1
Arming preparation state*2 ON ON
Armed state OFF BLINKING
Alarm sounding state ON ON

*1: w/ Engine Immobiliser System

*2: w/ Theft Warning ECU Assembly


Blinking Cycle
Time Security Indicator light
0.2 seconds. ON
1.8 seconds. OFF