Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003008 METER / GAUGE / DISPLAY _0015206 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The combination meter assembly controls the fuel receiver gauge in accordance with the resistance of the fuel sender gauge that varies depending on the amount of fuel remaining in the fuel tank.

WIRING DIAGRAM

E236728E02
4.688,2.958 5.281,3.292 0.594,0.333 10 E34 4.688,3.125 6.927,3.563 2.24,0.438 10 Combination Meter Assembly 2.094,1.667 3.865,2.333 1.771,0.667 10 Fuel Pump Assembly 2.094,1.5 2.698,1.958 0.604,0.458 10 P1 3.188,1.052 3.625,1.563 0.438,0.51 10 2 2.177,1.042 2.667,1.479 0.49,0.438 10 1 4.75,1.042 5.281,1.479 0.531,0.438 10 19 5.052,1.135 5.469,1.479 0.417,0.344 10 +

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (FUEL PUMP ASSEMBLY)
E236729C01
1.458,0.073 1.948,0.365 0.49,0.292 0.146,0.104 0.531,0.469 0.385,0.365 10 *a 1.615,0.135 2.115,0.448 0.5,0.313 10 P1
*a Front view of harness connector
(to Fuel Pump Assembly)


a.

Disconnect the P1 fuel pump assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the position of the receiver gauge needle.

OK:

Needle position is on EMPTY.



d.

Connect terminals 1 and 2 on the wire harness side connector.


e.

Turn the ignition switch to ON.


f.

Check the position of the receiver gauge needle.

OK:

Needle position is on FULL.


Result:
Proceed to
OK
NG




OK

2.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP ASSEMBLY - COMBINATION METER AND BODY GROUND)
2.INSPECT FUEL SENDER GAUGE ASSEMBLY
E236810C03
0.198,0.198 0.521,0.583 0.323,0.385 10 *a 0.365,2.479 0.75,2.865 0.385,0.385 10 F 0.583,4.354 0.927,4.604 0.344,0.25 10 E 0.229,3.385 0.74,3.74 0.51,0.354 10 1/2
*a Component without harness connected
(Fuel Sender Gauge Assembly)


a.

Remove the fuel sender gauge assembly.


b.

Check that the float position is between E and F.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Float Level Float Position Specified Condition
1 - 2 F 0 mm 13.5 to 16.5 Ω
1/2 73.8 to 85.8 mm 176.9 to 201.9 Ω
E 162.5 to 174.5 mm 405.5 to 414.5 Ω


Result:
Proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP ASSEMBLY - COMBINATION METER AND BODY GROUND)
E236811C01
1.531,0.365 1.948,0.635 0.417,0.271 1.542,2.573 1.958,2.844 0.417,0.271 2.917,3.531 2.708,2.813 true 1.656,0.417 2.188,0.875 0.531,0.458 10 P1 1.625,2.625 2.177,3.042 0.552,0.417 10 E34 0.177,0.25 0.583,0.646 0.406,0.396 10 *a 0.177,2.448 0.656,2.833 0.479,0.385 10 *b 2.625,2.604 3.01,2.958 0.385,0.354 10 +
*a Front view of wire harness connector
(to Fuel Pump Assembly)
*b Front view of wire harness connector
(to Combination Meter Assembly)


a.

Disconnect the P1 fuel pump assembly connector.


b.

Disconnect the E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
P1-2 - E34-19 (+) Always Below 1 Ω
P1-1 - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
P1-2 or E34-19 (+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR