Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals ECUT and E of the DLC3. The DTCs are communicated through SRS warning light blinking patterns.

HINT:

When one or more of the warning lights blink continuously, the cause may be a ground short in the wiring of terminal ECUT of the DLC3 or an internal ground short in an ECU.


WIRING DIAGRAM

C240459E05
5.302,2.75 7.125,3.177 1.823,0.427 10 CENTER AIRBAG SENSOR ASSEMBLY 5.813,1.135 5.99,1.323 0.177,0.188 10 T 0.646,2.333 1.01,2.479 0.365,0.146 10 E12 0.646,2.5 1.063,2.667 0.417,0.167 10 DLC3 1.354,1.167 1.792,1.354 0.438,0.188 10 ECUT 1.625,1.927 1.781,2.135 0.156,0.208 10 E 5.51,1.052 5.823,1.24 0.313,0.188 10 10 1.854,1.052 2.167,1.24 0.313,0.188 10 13 1.906,1.813 2.219,2 0.313,0.188 10 4 5.313,2.583 5.625,2.771 0.313,0.188 10 E60

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DLC3 - CENTER AIRBAG SENSOR AND BODY GROUND)
a.
C271021C01
1.573,0.167 2,0.417 0.427,0.25 1.667,2.25 2.083,2.5 0.417,0.25 1.833,0.844 2.333,0.427 true 2,1.354 2.417,1.688 true 2.104,3.292 2.573,3.656 true 0.25,0.25 0.563,0.448 0.313,0.198 10 *a 0.25,2.323 0.563,2.521 0.313,0.198 10 *b 1.656,0.219 2.115,0.417 0.458,0.198 10 E12 1.74,2.302 2.198,2.5 0.458,0.198 10 E60 2.427,0.302 2.583,0.5 0.156,0.198 10 E 2.49,1.677 3.104,1.875 0.615,0.198 10 ECUT 2.51,3.75 3,4 0.49,0.25 10 10 (T)
*a Front view of DLC3
*b Rear view of wire harness connector
(to Center Airbag Sensor Assembly)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the E60 connector from the center airbag sensor assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-13 (ECUT) - E60-10 (T) Always Below 1 Ω
E12-4 (E) - Body ground Always Below 1 Ω
E60-10 (T) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR