Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located on the combination meter. When the ignition switch is turned from off to ON, the SRS warning light illuminates. If the SRS is normal, the SRS warning light turns off automatically after approximately 6 seconds. If there is a malfunction in the SRS, the SRS warning light remains illuminated even after approximately 6 seconds have passed. When terminals ECUT and E of the DLC3 are connected, the DTCs are communicated through SRS warning light blinking patterns.

WIRING DIAGRAM

C251587E02
3.802,2.083 4.25,2.25 0.448,0.167 10 A/B 3.156,2.667 3.417,2.813 0.26,0.146 10 IG 3.156,4.25 3.417,4.396 0.26,0.146 10 E 2.979,5.635 3.281,5.802 0.302,0.167 10 E34 5.656,5.646 5.99,5.813 0.333,0.167 10 E60 0.063,2.667 1.333,2.875 1.271,0.208 10 from Ignition Switch 0.063,0.865 1.333,1.073 1.271,0.208 10 from Ignition Switch 1.99,1.042 2.615,1.24 0.625,0.198 10 ECU IG1 1.99,2.833 2.615,3.031 0.625,0.198 10 ECU IG2 2.906,2.563 3.156,2.771 0.25,0.208 10 39 2.906,4.135 3.115,4.344 0.208,0.208 10 16 6.146,2.083 6.583,2.229 0.438,0.146 10 LA 4.135,1.969 4.406,2.135 0.271,0.167 10 17 5.875,1.979 6.135,2.167 0.26,0.188 10 21 5.875,4.146 6.104,4.333 0.229,0.188 10 19 6.146,4.25 6.385,4.417 0.24,0.167 10 E1 5.927,0.729 6.104,0.885 0.177,0.156 10 9 6.146,0.833 6.5,0.99 0.354,0.156 10 IG1 2.969,5.792 4.74,6.271 1.771,0.479 10 COMBINATION METER ASSEMBLY 5.667,5.802 7.083,6.323 1.417,0.521 10 CENTER AIRBAG SENSOR ASSEMBLY

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.INSPECT BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK CONNECTION OF CONNECTOR

NG

RECHARGE OR REPLACE BATTERY

2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor assembly and combination meter.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR ASSEMBLY)

NG

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR ASSEMBLY)
a.
C198037C01
0.583,0.917 1,1.167 0.417,0.25 2.021,1.313 2.385,1.219 true 1.865,1.469 2.396,1.615 true 0.656,0.969 0.948,1.125 0.292,0.156 10 E60 1.625,0.26 1.917,0.417 0.292,0.156 10 *a 2.5,1.542 3.083,1.698 0.583,0.156 10 19 (E1) 2.438,1.125 2.917,1.281 0.479,0.156 10 9 (IG1)
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)


Disconnect the connector from the center airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E60-9 (IG1) - Body ground Ignition switch ON 11 to 14 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E60-19 (E1) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)
a.
H100390C01
1.5,0.417 1.917,0.667 0.417,0.25 2.677,0.802 2.302,1.208 true 2.625,1.417 2.833,1.688 true 1.583,0.469 1.885,0.667 0.302,0.198 10 E34 0.094,0.063 0.281,0.26 0.188,0.198 10 *a 2.875,1.635 3.135,1.833 0.26,0.198 10 IG 2.75,0.708 3.01,0.906 0.26,0.198 10 E
*a Front view of wire harness connector
(to Combination Meter)


Disconnect the E34 connector from the combination meter.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E34-39 (IG) - Body ground Ignition switch ON 11 to 14 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-16 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR
a.
C251588C01
1.427,2.75 1.917,3 0.49,0.25 1.417,0.25 1.917,0.5 0.5,0.25 2.698,3.125 2.479,3.5 true 1.563,1.417 1.313,1.854 true 0.177,2.708 0.438,2.969 0.26,0.26 10 *b 0.177,0.135 0.438,0.396 0.26,0.26 10 *a 1.542,2.792 1.833,2.948 0.292,0.156 10 E34 1.531,0.302 1.823,0.458 0.292,0.156 10 E60 0.854,1.885 1.427,2.083 0.573,0.198 10 21 (LA) 2.667,2.927 2.99,3.125 0.323,0.198 10 A/B
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Combination Meter)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E60-21 (LA) - E34-17 (A/B) Always Below 1 Ω
E60-21 (LA) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

6.CHECK CENTER AIRBAG SENSOR ASSEMBLY

NG

REPLACE HARNESS AND CONNECTOR

6.CHECK CENTER AIRBAG SENSOR ASSEMBLY
a.

Connect the E34 combination meter assembly connector.


b.
C198037C02
1.5,0.25 1.917,0.5 0.417,0.25 1.594,1.469 1.313,1.854 true 0.135,0.115 0.333,0.313 0.198,0.198 10 *a 1.573,0.292 1.865,0.448 0.292,0.156 10 E60 0.729,1.823 1.313,1.979 0.583,0.156 10 21 (LA)
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)


Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E60-21 (LA) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

7.REPLACE CENTER AIRBAG SENSOR ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

7.REPLACE CENTER AIRBAG SENSOR ASSEMBLY
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

d.

Check the SRS warning light condition.

OK:

SRS warning light illuminates normally.


Result:
Proceed to
OK
NG




OK

END (CENTER AIRBAG SENSOR IS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY