Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY › 2011.11–2013.07
RM19Y0E _58 Vehicle Interior _003011 SEAT _0015215 REAR NO. 1 SEAT ASSEMBLY A

SEAT  REAR NO. 1 SEAT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp surfaces on the rear seat back frame sub-assembly and rear seat cushion frame sub-assembly could cause injuries to your hands.


HINT:

The procedure described below is for RH side. Use the same procedure for both RH and LH side, unless otherwise specified.


PROCEDURE

Hide 71621A 1.INSTALL REAR SEAT CUSHION SILENCER PAD

B292447

a.

Install the rear seat cushion silencer pad to rear seat cushion pad.


Hide 71611A 2.INSTALL REAR SEAT CUSHION PAD

B292446

a.

Install the rear seat cushion pad to the rear seat cushion frame sub-assembly.


Hide 71075S 3.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

a.
B292448C02
0.438,2.854 0.563,2.917 true 1.875,4.177 1.708,4.385 true 0.25,2.76 0.688,3.156 0.438,0.396 10 *1 1.552,4.354 1.938,4.635 0.385,0.281 10 *2
*1 New Hog Ring
*2 Hog Ring Pliers


Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad with 6 new hog rings.

NOTICE:
·

Do not soil or scratch the separate type rear seat cushion cover.

·

When installing the hog rings, minimize wrinkles as much as possible.




b.
B292449C02
0.438,2.854 0.563,2.917 true 1.875,4.177 1.698,4.375 true 0.25,2.75 0.667,3.115 0.417,0.365 10 *1 1.542,4.333 1.865,4.604 0.323,0.271 10 *2
*1 New Hog Ring
*2 Hog Ring Pliers


Using hog ring pliers, install the rear seat cushion frame sub-assembly with the 5 new hog rings.

NOTICE:
·

Do not soil or scratch the separate type rear seat cushion cover.

·

When installing the hog rings, minimize wrinkles as much as possible.




c.
B292443

Close the fastener.


Hide 72695A 4.INSTALL REAR SEAT LOCK CONTROL CABLE (for Slide Seat Type)

B296100C03
1.49,1.083 1.458,2.125 1.458,2.125 1.031,1.094 true 1.396,2.135 1.802,2.521 0.406,0.385 10 *1
*1 New Band


a.

Engage the clamp.


b.

Install the seat lock control cable with new 2 bands.


Hide 72695A 5.INSTALL REAR SEAT LOCK CONTROL CABLE (for Non-slide Seat Type)

B292442C02
2.271,1.573 1.854,1.323 true 1.656,1.219 2.073,1.625 0.417,0.406 10 *1
*1 New Band


a.

Engage the 2 clamps.


b.

Install the seat lock control cable with a new band.


Hide 72160 6.INSTALL REAR SEAT OUTER TRACK ASSEMBLY (for Slide Seat Type)

a.
B292441

Install the rear seat outer track assembly with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 72170C 7.INSTALL REAR NO. 1 SEAT INNER TRACK ASSEMBLY (for Slide Seat Type)

HINT:

Use the same procedures as for the rear seat outer track assembly.


Hide 71308E 8.INSTALL REAR SEAT LEG SUB-ASSEMBLY (for Slide Seat Type)

B292440

a.

Install the rear seat leg sub-assembly with the 3 nuts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 9.INSTALL REAR NO. 1 SEAT CUSHION OUTER LEG (for Non-slide Seat Type)

a.
B296878C02
0.677,0.5 1.26,0.708 true 0.99,0.167 1.563,0.563 true 0.688,1.177 1.229,0.792 true 0.49,0.417 0.885,0.802 0.396,0.385 10 *1 0.51,1.125 0.906,1.5 0.396,0.375 10 *2 0.802,0.073 1.167,0.375 0.365,0.302 10 *3
*1 E ring
*2 Pin
*3 Rear No. 1 Seat Turn Spring


Install the rear No. 1 seat turn spring and rear No. 1 seat cushion outer leg with the E ring and pin.


Hide 10.INSTALL REAR NO. 1 SEAT CUSHION INNER LEG (for Non-slide Seat Type)

HINT:

Use the same procedures as for the rear No. 1 seat outer leg.


Hide 72670B 11.INSTALL REAR SEAT CUSHION LOCK ASSEMBLY (for Slide Seat Type)

a.
B296096C04
0.385,1.448 1.021,1.573 true 0.198,1.354 0.594,1.74 0.396,0.385 10 *1
*1 Rear Seat Lock Control Cable


Install the rear seat cushion lock assembly with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


b.

Engage the clamp and connect the rear seat lock control cable.


Hide 72670B 12.INSTALL REAR SEAT CUSHION LOCK ASSEMBLY (for Non-slide Seat Type)

a.
B292439C02
0.552,1.26 1.24,1.74 true 0.375,1.156 0.792,1.573 0.417,0.417 10 *1
*1 Rear Seat Lock Control Cable


Install the rear seat cushion lock assembly with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


b.

Engage the clamp and connect the rear seat lock control cable.


Hide 73330 13.INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY

Hide 72694 14.INSTALL REAR SEAT CUSHION LOCK COVER (for Slide Seat Type)

B296094

a.

Install the rear seat cushion lock cover with 2 screws.


Hide 72694 15.INSTALL REAR SEAT CUSHION LOCK COVER (for Non-slide Seat Type)

B296880

a.

Install the rear seat cushion lock cover with 2 screws.


Hide 16.INSTALL REAR SEAT LEG COVER (for Slide Seat Type)

B296093

a.

Install the rear seat cushion and rear seat leg cover with the screw.


Hide 71324A 17.INSTALL REAR SEAT CUSHION (for Non-slide Seat Type)

a.
B296879

Install the rear seat cushion with the screw.


Hide 72159A 18.INSTALL REAR SEAT TRACK BRACKET COVER (for Slide Seat Type)

B296092

a.

Attach the 4 claws and install the 2 seat track bracket covers.


Hide 71671 19.INSTALL REAR SEAT BACK SILENCER PAD

B292433

a.

Install the rear seat back silencer pad to separate type rear seat back pad.


Hide 71651S 20.INSTALL SEPARATE TYPE REAR SEAT BACK PAD

B292432

a.

Install the separate type rear seat back pad to the rear seat back frame sub-assembly.


Hide 71077S 21.INSTALL SEPARATE TYPE REAR SEAT BACK COVER

a.
B292450C02
0.438,2.854 0.563,2.917 true 1.875,4.177 1.719,4.375 true 0.25,2.76 0.698,3.208 0.448,0.448 10 *1 1.563,4.344 1.927,4.656 0.365,0.313 10 *2
*1 New Hog Ring
*2 Hog Ring Pliers


Using hog ring pliers, install the separate type rear seat back cover to the separate type rear seat back pad with 3 new hog rings.

NOTICE:
·

Do not soil or scratch the separate type rear seat back cover.

·

When installing the hog rings, minimize wrinkles as much as possible.




b.
B292451C02
0.438,2.854 0.563,2.917 true 1.875,4.177 1.75,4.385 true 0.25,2.76 0.677,3.198 0.427,0.438 10 *1 1.594,4.354 1.958,4.667 0.365,0.313 10 *2
*1 New Hog Ring
*2 Hog Ring Pliers


Using hog ring pliers, install 3 new hog rings.

NOTICE:
·

Do not soil or scratch the separate type rear seat back cover.

·

When installing the hog rings, minimize wrinkles as much as possible.




c.
B292429

Attach the hook.


Hide 71931A 22.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

a.
B296109C06
1.802,0.823 2.573,1.188 true 1.635,0.729 2.083,1.135 0.448,0.406 10 *1
*1 Protruding Portion


Align the protruding portion of the rear seat headrest support assembly with the installation groove of the rear seat back frame sub-assembly.


b.

Attach the 2 claws and install the rear seat headrest support assembly.


Hide 71931B 23.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT

a.
B296112C06
1.792,0.75 1.813,1.167 1.813,1.167 1.573,0.75 true 1.76,1.198 2.146,1.531 0.385,0.333 10 *1
*1 Protruding Portion


Align the protruding portion of the rear No. 1 seat headrest support with the installation groove of the rear seat back frame sub-assembly.


b.

Attach the 2 claws and install the rear No. 1 seat headrest support.


Hide 71970 24.INSTALL REAR SEAT HEADREST ASSEMBLY

a.
B292428C04
2.958,1.156 3.104,1.583 true 3.063,1.604 3.417,1.927 0.354,0.323 10 *1
*1 Lock Button


Push in the lock button of the rear seat headrest support assembly and install the rear seat headrest assembly.


Hide 25.INSTALL REAR NO. 1 SEAT BACK ASSEMBLY

a.
B292427C04
2.021,2.292 2.698,2.063 true 2.344,0.948 2.458,1.24 true 1.813,2.229 2.229,2.563 0.417,0.333 10 *1 2.417,1.281 2.771,1.604 0.354,0.323 10 *2
*1 E Ring
*2 Bushing


Install the bushing.


b.

Install the rear No. 1 seat back assembly with the 2 bolts and E ring.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 71878A 26.INSTALL REAR SEAT INNER RECLINING COVER

a.
B292426

Engage the claw and install the seat inner reclining cover.


Hide 79011 27.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY

a.
B292424

Engage the 4 claws and install the No.1 seat cushion cover sub-assembly.


b.

Install the 2 screws.


Hide 71833A 28.INSTALL REAR NO. 1 SEAT RECLINING COVER

a.
B292425

Engage the 2 claws and install the rear No. 1 seat reclining cover.


b.

Install the screw.


Hide 72637A 29.INSTALL REAR SEAT LOCK HANDLE

a.
B292435C02
0.698,1.5 1.344,1.385 true 0.51,1.438 0.99,1.792 0.479,0.354 10 *1
*1 New Snap Ring


Install the rear seat lock handle with a new snap ring.