Wear protective gloves. Sharp surfaces on the rear No. 2 seat back frame sub-assembly and No. 2 seat cushion spring assembly could cause injuries to your hands.
71308E
1.INSTALL REAR SEAT LEG BRACKET RH
| *1 | E Ring |
| *2 | Bushing |
| *3 | Pin |
Install the rear seat leg bracket RH with the E ring, 2 bushings and pin.
71309C
2.INSTALL REAR SEAT LEG BRACKET LH
Use the same procedure as for the RH side.
71622A
3.INSTALL REAR SEAT CUSHION SILENCER PAD
Install the rear seat cushion silencer pad to the No. 2 seat cushion pad.
79235
4.INSTALL NO. 2 SEAT CUSHION PAD
Install the No. 2 seat cushion pad to the No. 2 seat cushion spring assembly.
79021A
5.INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY
| *1 | New Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly to the No. 2 seat cushion pad with 6 new hog rings.
Do not soil or scratch the No. 2 seat cushion cover sub-assembly.
When installing the hog rings, minimize wrinkles as much as possible.
| *1 | New Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install 12 new hog rings.
Do not soil or scratch the No. 2 seat cushion cover sub-assembly.
When installing the hog rings, minimize wrinkles as much as possible.
Close the fastener.
79205
6.INSTALL NO. 2 SEAT LEG SUB-ASSEMBLY
| *1 | E Ring |
| *2 | Pin |
Install the No. 2 seat leg sub-assembly with 2 E rings and 2 pins.
Install the 2 tension springs.
72680C
7.INSTALL REAR NO. 2 SEAT CUSHION LOCK ASSEMBLY
Install the rear No. 2 seat cushion lock assembly with the 2 bolts.
73350
8.INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY
79225B
9.INSTALL REAR NO. 2 SEAT CUSHION LOCK COVER
Install the 2 rear No. 2 seat cushion lock covers with the 2 screws.
79382C
10.INSTALL NO. 2 SEAT CUSHION
Install the 2 No. 2 seat cushions with the 2 screws.
71393
11.INSTALL REAR SEAT CUSHION BAND
Install the rear seat cushion band with the screw.
71672
12.INSTALL REAR SEAT BACK SILENCER PAD
Install the rear seat back silencer pad to the No. 2 seat back pad sub-assembly RH.
Use the same procedure for the LH side and RH side.
79275
13.INSTALL NO. 2 SEAT BACK PAD SUB-ASSEMBLY RH
Install the No. 2 seat back pad sub-assembly RH to the rear No. 2 seat back frame sub-assembly RH.
79275
14.INSTALL NO. 2 SEAT BACK PAD SUB-ASSEMBLY LH
Use the same procedure as for the RH side.
79023A
15.INSTALL NO. 2 SEAT BACK COVER SUB-ASSEMBLY RH
| *1 | New Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install the No. 2 seat back cover sub-assembly to the No. 2 seat back pad sub-assembly RH with 3 new hog rings.
Do not soil or scratch the rear No. 2 seat back cover sub-assembly.
When installing the hog rings, minimize wrinkles as much as possible.
Engage the hook and close the fastener.
79023A
16.INSTALL NO. 2 SEAT BACK COVER SUB-ASSEMBLY LH
Use the same procedure as for the RH side.
71931C
17.INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY
| *1 | Protruding Portion |
Align the protruding portion of the rear No. 2 seat headrest support assembly with the installation groove of the rear No. 2 seat back frame sub-assembly.
Engage the 2 claws and install the rear No. 2 seat headrest support assembly.
Use the same procedure for both sides.
71931C
18.INSTALL REAR NO. 2 SEAT HEADREST SUPPORT
| *1 | Protruding Portion |
Align the protruding portion of the rear No. 2 seat headrest support with the installation groove of the rear No. 2 seat back frame sub-assembly.
Engage the 2 claws and install the rear No. 2 seat headrest support.
Use the same procedure for the both sides.
71940A
19.INSTALL REAR SEAT HEADREST ASSEMBLY
| *1 | Lock Button |
Push in the lock button of the rear seat headrest support assembly and install the rear seat headrest assembly.
Use the same procedure for the both sides.
20.INSTALL REAR NO. 2 SEAT BACK ASSEMBLY RH
| *1 | Bushing |
Install the bushing and rear No. 2 seat back assembly RH.
21.INSTALL REAR NO. 2 SEAT BACK ASSEMBLY LH
Use the same procedure as for the RH side.
71303C
22.INSTALL REAR SEAT BACK HINGE SUB-ASSEMBLY RH
| *1 | Bushing |
Install the rear seat back hinge sub-assembly RH with 3 bolts and bushing.
71304B
23.INSTALL REAR NO. 2 SEAT HINGE SUB-ASSEMBLY LH
Use the same procedure as for the rear seat back hinge sub-assembly RH.
71485
24.INSTALL NO. 2 SEAT BACK COVER
Install the No. 2 seat back cover with the 2 screws.
79273
25.INSTALL NO. 2 SEAT HINGE COVER
Use the same procedure as for the No. 2 seat back cover.