Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for 3SZ-VE) › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003013 HEATING / AIR CONDITIONING _0015230 COMPRESSOR(for 3SZ-VE) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 3SZ-VE)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.

When replacing the compressor with a new one, gradually release the refrigerant gas from the service valve and drain the following amount of oil from the new compressor before installation.

Standard:

(Oil capacity inside the new compressor: 80 to 95 cc (2.7 to 3.2 fl. oz.)) - (Remaining oil amount in the removed compressor) = (Oil amount to be removed from the new compressor)


NOTICE:
·

When checking the compressor oil level, follow the A/C system precautions.

·

Since compressor oil remains in the pipes of the vehicle, if a new compressor is installed without removing some oil from the compressor, the oil amount becomes excessive. Excessive oil prevents heat exchange in the refrigerant cycle and causes refrigeration system failure.

·

If the volume of oil remaining in the removed compressor is too small, check for oil leakage.

·

Be sure to use ND-OIL 8 for compressor oil.




Hide 88320 2.INSTALL COOLER COMPRESSOR ASSEMBLY

a.
E231781N02
2.781,1.578 2.882,1.759 0.101,0.181 10 1 2.505,1.825 2.606,2.006 0.101,0.181 10 2 2.103,1.916 2.203,2.097 0.101,0.181 10 3 2.617,1.118 2.718,1.299 0.101,0.181 10 4

for RHD:

i.

Install the cooler compressor assembly with the 4 bolts and 3 cooler brackets.

Torque:
26 N*m (269 kgf*cm, 20 ft.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



ii.

Connect the connector.



b.
E238737N01
2.771,1.604 3.104,1.927 0.333,0.323 10 1 2.104,1.948 2.458,2.177 0.354,0.229 10 3 2.51,1.813 2.865,2.167 0.354,0.354 10 2 2.646,1.125 2.99,1.427 0.344,0.302 10 4

for LHD:

i.

Install the cooler compressor assembly with the 4 bolts.

Torque:
26 N*m (269 kgf*cm, 20 ft.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



ii.

Connect the connector.



Hide 88712D 3.CONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE

a.

Remove the attached vinyl tape from the No. 1 cooler refrigerant suction hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant suction hose.


d.

Connect the No. 1 cooler refrigerant suction hose to the cooler compressor assembly with the bolt.

Torque:
7.9 N*m (81 kgf*cm, 70 in.*lbf)


Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Remove the attached vinyl tape from the No. 1 cooler refrigerant discharge hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.


d.

Connect the No. 1 cooler refrigerant discharge hose to the cooler compressor assembly with the bolt.

Torque:
7.9 N*m (81 kgf*cm, 70 in.*lbf)


Hide 16361A 5.INSTALL FAN AND GENERATOR V BELT

Hide 7. WARM UP ENGINE