Home › Vehicle Exterior › DOOR / HATCH › HOOD › 2011.11–2015.08
RM19Y0E _59 Vehicle Exterior _003017 DOOR / HATCH _0015260 HOOD N

DOOR / HATCH  HOOD  ADJUSTMENT  


CAUTION / NOTICE / HINT

B211130C04
0.667,0.208 1.344,0.698 0.677,0.49 10 *1 2.573,0.219 3.052,0.625 0.479,0.406 10 *2
*1 Centering Bolt
*2 Standard Bolt


HINT:
·

Centering bolts are used to mount the hood hinge and the hood lock. The hood and the hood lock cannot be adjusted with the centering bolts in. Substitute standard bolts (with flange) for the centering bolts when making adjustments.



PROCEDURE

Hide 53301 1.INSPECT HOOD SUB-ASSEMBLY

a.

Check that the clearance measurements are within the standard ranges.

B290261
1.073,2.469 1.417,2.771 0.344,0.302 10 *A 2.583,3.719 2.927,4.021 0.344,0.302 10 *B 3.052,0.51 3.573,0.813 0.521,0.302 10 *a 5.625,2.427 5.979,2.74 0.354,0.313 10 *b 5.823,3 6.125,3.302 0.302,0.302 10 *c 4.906,2.958 5.198,3.198 0.292,0.24 10 *d 1.646,2.583 1.938,2.865 0.292,0.281 10 *e 1.698,3.333 1.958,3.635 0.26,0.302 10 *f 3.271,3.823 3.594,4.104 0.323,0.281 10 *g 3.333,4.635 3.635,4.885 0.302,0.25 10 *h
*A Standard Type *B Aero Type


Standard:
Area Measurement Area Measurement
*a 8.0 mm
(0.315 in.)
*b 2.0 to 5.0 mm
(0.079 to 0.197 in.)
*c -1.5 to 1.5 mm
(-0.059 to 0.059 in.)
*d 6.9 mm
(0.272 in.)
*e 4.2 to 7.2 mm
(0.165 to 0.284 in.)
*f 1.2 to 4.2 mm
(0.047 to 0.165 in.)
*g 4.0 to 7.0 mm
(0.158 to 0.276 in.)
*h 1.3 to 4.3 mm
(0.051 to 0.169 in.)



Hide 53301 2.ADJUST HOOD SUB-ASSEMBLY

a.
B161310

Loosen the 4 hood side hinge bolts.


b.

Move the hood to adjust the clearance to within the standard range.


c.

Tighten the 4 hood side hinge bolts after the adjustment.

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)


d.
B290263

Adjust the height of the hood front end by turning the 2 center hood cushions.

HINT:

The center hood cushion can be raised and lowered by turning it.



e.

Adjust the hood lock.

i.

Remove the front bumper cover.


ii.

Remove the No. 1 hood lock control cable cover. (for RHD)


iii.

Remove the No. 2 hood lock control cable cover. (for LHD)


iv.
B297765

Loosen the 3 bolts.


v.
B297766

Adjust the hood lock position so that the striker can enter it smoothly.


vi.

Tighten the 3 bolts after the adjustment.

Torque:
7.5 N*m (77 kgf*cm, 66 in.*lbf)



f.
B290263

Adjust the operating force to close the hood by turning the 2 center hood cushions as shown in the illustration.

HINT:

The center hood cushion can be raised and lowered by turning it.