Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM19Y0E _59 Vehicle Exterior _003017 DOOR / HATCH _0015262 FRONT DOOR N

DOOR / HATCH  FRONT DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B211130
0.667,0.198 1.229,0.573 0.563,0.375 10 *1 2.552,0.188 3.021,0.563 0.469,0.375 10 *2
*1 Centering Bolt
*2 Standard Bolt


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures described below are for the RH side.

·

Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute standard bolts (with flange) for the centering bolts when making adjustments.



PROCEDURE

Hide 67111 1.INSPECT FRONT DOOR

a.

Check that the clearance measurements are within the standard ranges.

B297790
6.427,0.823 6.74,1.125 0.313,0.302 10 *a 5.802,0.604 6.083,0.844 0.281,0.24 10 *b 4.104,0.5 4.365,0.781 0.26,0.281 10 *c 4.438,1 4.729,1.26 0.292,0.26 10 *d 2.625,0.531 2.906,0.792 0.281,0.26 10 *c 2.885,1.125 3.167,1.385 0.281,0.26 10 *d 0.958,1.49 1.281,1.75 0.323,0.26 10 *c 1.521,1.719 1.823,1.99 0.302,0.271 10 *e 0.375,4.281 0.656,4.552 0.281,0.271 10 *f 1,4.094 1.323,4.365 0.323,0.271 10 *g 2.906,4.677 3.198,4.958 0.292,0.281 10 *i 2.781,5.01 3.052,5.25 0.271,0.24 10 *h 4.458,4.646 4.729,4.917 0.271,0.271 10 *j 4.323,4.948 4.615,5.219 0.292,0.271 10 *h 5.844,4.354 6.135,4.656 0.292,0.302 10 *g 6.458,4.51 6.729,4.781 0.271,0.271 10 *k

Standard:
Area Measurement Area Measurement
*a 3.6 to 6.6 mm
(0.201 to 0.260 in.)
*b -1.6 to 1.4 mm
(-0.063 to 0.055 in.)
*c 4.0 to 7.0 mm
(0.158 to 0.276 in.)
*d 5.9 to 8.9 mm
(0.232 to 0.350 in.)
*e 7.5 to 10.5 mm
(0.295 to 0.413 in.)
*f 3.5 to 6.5 mm
(0.138 to 0.256 in.)
*g -1.5 to 1.5 mm
(-0.059 to 0.059 in.)
*h 4.5 to 7.5 mm
(0.177 to 0.295 in.)
*i 5.5 to 8.5 mm
(0.217 to 0.335 in.)
*j 4.8 to 7.8 mm
(0.189 to 0.307 in.)
*k 3.5 to 6.5 mm
(0.138 to 0.256 in.)
- -



Hide 67111 2.ADJUST FRONT DOOR

a.
B297791

Using SST, adjust the door horizontally and vertically by loosening the body side hinge bolts.

SST
09812-00010  


b.

Tighten the body side hinge bolts after the adjustment.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


c.
B297792

Adjust the door horizontally and vertically by loosening the door side hinge bolts.


d.

Tighten the door side hinge bolts after the adjustment.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


e.
B297793

Adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


f.

Tighten the striker mounting screws after the adjustment.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)