Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM19Y0E _59 Vehicle Exterior _003017 DOOR / HATCH _0015263 REAR DOOR N

DOOR / HATCH  REAR DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B211130
0.667,0.24 1.146,0.646 0.479,0.406 10 *1 2.552,0.24 2.969,0.594 0.417,0.354 10 *2
*1 Centering Bolt
*2 Standard Bolt


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures described below are for the RH side.

·

Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute standard bolts (with flange) for the centering bolts when making adjustments.



PROCEDURE

Hide 67114 1.INSPECT REAR DOOR

a.

Check that the clearance measurements are within the standard ranges.

B297810
0.719,0.729 1.063,1.01 0.344,0.281 10 *f 1.354,0.948 1.667,1.208 0.313,0.26 10 *e 4.208,0.406 4.573,0.688 0.365,0.281 10 *c 4.729,0.917 5.01,1.146 0.281,0.229 10 *d 5.458,0.938 5.854,1.229 0.396,0.292 10 *b 6.271,0.531 6.573,0.792 0.302,0.26 10 *a 6.26,3.417 6.583,3.708 0.323,0.292 10 *h 6.76,3.656 7.052,3.917 0.292,0.26 10 *k 5.177,4.427 5.448,4.667 0.271,0.24 10 *h 5.625,4.938 5.875,5.156 0.25,0.219 10 *k 3.99,4.771 4.302,5.073 0.313,0.302 10 *j 3.844,5.063 4.177,5.365 0.333,0.302 10 *i 1.26,4.427 1.573,4.708 0.313,0.281 10 *h 1.833,4.615 2.219,4.938 0.385,0.323 10 *g

Standard:
Area Measurement Area Measurement
*a 6.2 to 9.2 mm
(0.244 to 0.362 in.)
*b 5.1 to 8.1 mm
(0.201 to 0.319 in.)
*c 4.0 to 7.0 mm
(0.158 to 0.276 in.)
*d 7.1 to 10.1 mm
(0.280 to 0.398 in.)
*e 3.6 to 6.6 mm
(0.142 to 0.260 in.)
*f -1.6 to 1.4 mm
(0.063 to 0.055 in.)
*g 3.5 to 6.5 mm
(0.138 to 0.256 in.)
*h -1.5 to 1.5 mm
(0.059 to 0.059 in.)
*i 4.5 to 7.5 mm
(0.177 to 0.295 in.)
*j 5.0 to 8.0 mm
(0.197 to 0.315 in.)
*k 3.0 to 6.0 mm
(0.118 to 0.236 in.)
- -



Hide 67114 2.ADJUST REAR DOOR

a.
B297811

Adjust the door horizontally and vertically by loosening the body side hinge bolts.


b.

Tighten the body side hinge bolts after the adjustment.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


c.
B312697

Adjust the door horizontally and vertically by loosening the door side hinge bolts.


d.

Tighten the door side hinge bolts after the adjustment.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


e.
B297813

Adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


f.

Tighten the striker mounting screws after the adjustment.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)