Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › 2011.11–2015.08
RM19Y0E _59 Vehicle Exterior _003019 WIPER / WASHER _0015272 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LHD and RHD vehicle.

·

The procedure listed below is for the RHD vehicle.



PROCEDURE

Hide 85160 1.INSTALL WINDSHIELD WIPER LINK ASSEMBLY

a.

Install the windshield wiper link assembly with the 6 nuts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


b.
E231711
1.469,0.521 1.865,0.979 true 2.531,1.583 2.271,1.219 true 1.281,0.417 1.677,0.813 0.396,0.396 10 *1 2.479,1.583 2.854,1.938 0.375,0.354 10 *2
*1 Windshield Wiper Link Assembly Hook
*2 Service Hole


Hook the windshield wiper link assembly hook on the edge of service hole.


Hide 55781E 2.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Engage the 8 guides and install the cowl top ventilator louver sub-assembly.


b.

Engage the 7 claws.


c.

Install the 2 clips.


Hide 53383 3.INSTALL HOOD TO COWL TOP SEAL

a.

Engage the 7 clips to install the hood to cowl top seal.


Hide 53446 4.INSTALL HOOD HINGE COVER LH

a.
E236913

Engage the clip indicated by the arrow as shown in the illustration to install the hood hinge cover LH.


b.
E231729

Engage the guide.


c.

Engage the 3 claws.


Hide 53445 5.INSTALL HOOD HINGE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 85221B 6.INSTALL FRONT WIPER ARM AND BLADE LH

a.
E238922
1.698,1.219 2.594,0.875 true 1.979,3.479 2.75,3.344 true 0.635,4.135 0.635,3.531 true 2.625,0.781 3.083,1.208 0.458,0.427 10 *a 2.771,3.25 3.24,3.615 0.469,0.365 10 *b 0.531,4.188 0.948,4.563 0.417,0.375 10 *1
*1 Wire Brush
*a Wiper Arm Serration
*b Wiper Pivot Serration


Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).


b.

Clean the wiper pivot serrations with a wire brush.


c.

Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

HINT:

Temporarily connect the cable to the negative battery terminal when checking the operation.



d.
E220880
2.333,1.208 1.719,1.896 true 2.542,3.719 2.99,4.094 true 2.365,1.104 2.563,1.344 0.198,0.24 10 *a 2.354,3.594 2.771,3.958 0.417,0.365 10 *a
*a Mark for Blade Position


Align the blade tip with the mark on the windshield glass.


e.

Tighten the nut of the front wiper arm.

Torque:
20 N*m (205 kgf*cm, 15 ft.*lbf)


Hide 85211B 7.INSTALL FRONT WIPER ARM AND BLADE RH

HINT:

Use the same procedure as for the LH side.


Hide 85292B 8.INSTALL FRONT WIPER ARM HEAD CAP

a.

Engage the claw and install the 2 front wiper arm head caps.


Hide 85110 9.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Engage the meshing of the crank arm pivot, and install the windshield wiper motor onto the windshield wiper link assembly.


b.

Unhook the windshield wiper link assembly hook.


c.

Install the windshield wiper motor with the 4 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


d.

Connect the connector.