Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › 2011.11–2015.08
RM19Y0E _59 Vehicle Exterior _003019 WIPER / WASHER _0015272 FRONT WIPER MOTOR G

WIPER / WASHER  FRONT WIPER MOTOR  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LHD and RHD vehicle.

·

The procedure listed below is for the RHD vehicle.



PROCEDURE

Hide 85110 1.INSPECT FRONT WIPER MOTOR ASSEMBLY

a.
E257938
0.781,1.042 1,1.042 1,1.042 1.417,1.396 true 2.594,1.073 2.417,1.073 2.417,1.073 1.917,1.438 true 1.906,1.719 2.5,1.896 2.5,1.896 2.667,1.896 true 0.792,1.844 1.01,1.844 1.01,1.844 1.427,1.708 true 0.563,0.958 0.99,1.271 0.427,0.313 10 LO 2.667,1.01 3.135,1.375 0.469,0.365 10 HI 0.552,1.76 1.135,2.177 0.583,0.417 10 +B 2.719,1.813 3.083,2.125 0.365,0.313 10 S 0.135,0.073 0.604,0.5 0.469,0.427 10 *a
*a Component without harness connected
(Windshield Wiper Motor Assembly)


Check the LO operation.

i.

Connect the positive (+) battery lead to terminal 2 (LO) of the connector and the negative (-) battery lead to the motor body, then check that the motor operates at low speed (LO).

Standard:

Motor operates at low speed (LO).


If the result is not as specified, replace the front wiper motor assembly.



b.

Check the HI operation.

i.

Connect the positive (+) battery lead to terminal 1 (HI) of the connector and the negative (-) battery lead to the motor body, then check that the motor operates at high speed (HI).

Standard:

Motor operates at high speed (HI).


If the result is not as specified, replace the front wiper motor assembly.



c.
E237844
1.354,1.125 1.354,0.333 1.354,0.333 1.458,0.333 true 1.854,3.375 1.854,2.583 1.854,2.583 1.75,2.583 true 0.146,0.063 0.573,0.49 0.427,0.427 12 *A 0.135,2.417 0.531,2.729 0.396,0.313 12 *B 1.479,0.26 1.833,0.531 0.354,0.271 10 *a 1.094,1.167 1.469,1.458 0.375,0.292 10 *b 1.938,3.438 2.281,3.781 0.344,0.344 10 *b 1.563,2.49 1.938,2.813 0.375,0.323 10 *a
*A for RHD
*B for LHD
*a Automatic Stop Position
*b 11° to 26°


Check the automatic stop operation.

i.

Connect the positive (+) battery lead to terminal 2 (LO) of the connector and the negative (-) battery lead to the motor body. With the motor operating at low speed (LO), disconnect terminal 2 (LO) to stop the wiper motor operation at any position other than the automatic stop position.


ii.

Using SST, connect terminals 3 (S) and 2 (+1). Connect the positive (+) battery lead to terminal 4 (+B) of the connector to restart the motor operation at low speed (LO).


iii.

Check that the motor stops automatically in the automatic stop position.

Standard:

Refer to the illustration.


If the result is not as specified, replace the front wiper motor assembly.