Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER RUBBER
RM19Y0E _59 Vehicle Exterior _003019 WIPER / WASHER _0015275 REAR WIPER RUBBER A

WIPER / WASHER  REAR WIPER RUBBER  REPLACEMENT  


PROCEDURE

Hide 85212A 1.REMOVE REAR WIPER BLADE

a.
E236904

Raise the wiper arm, and then detach the claw by rotating the wiper blade to the position where a "click" sound is heard as shown in the illustration.

NOTICE:

Be careful not to damage the claw.



b.
E123455

Pull the wiper blade straight toward the right side of the vehicle to remove it from the wiper arm.

NOTICE:

Do not fold the wiper arm with the wiper blade removed. The arm tip may damage the windshield surface.



Hide 85214A 2.REMOVE REAR WIPER RUBBER

a.
E178053
0.917,1.521 1.365,1.906 0.448,0.385 10 *a 1.896,0.052 2.333,0.438 0.438,0.385 10 *b 2.719,1.667 3.125,2.01 0.406,0.344 10 *d 2.625,1.021 3.021,1.375 0.396,0.354 10 *c
*a Stopper (Rear End of Blade)
*b Lightly Push (Grip)
*c Lift
*d Pull


Lift and pull the end of the wiper rubber protruding from the blade stopper as shown in the illustration to remove the wiper rubber.

NOTICE:

Do not forcibly pull out the wiper rubber. The backing plates will be deformed or the blade claws will be damaged.


HINT:

Lightly pushing the rubber between the ends and middle allows it to be removed more easily.



b.

Remove the 2 wiper rubber backing plates from the wiper rubber.


Hide 85214A 3.INSTALL REAR WIPER RUBBER

a.
E178054
0.677,0.24 0.438,0.24 0.438,0.24 0.438,1.833 true 1.708,2.76 1.708,2.188 true 0.708,0.167 1.021,0.427 0.313,0.26 10 *1 1.646,2.781 2.021,3.125 0.375,0.344 10 *1
*1 Backing Plate


Install the 2 backing plates as shown in the illustration.

NOTICE:

Install the backing plates so that they are facing in the correct direction.



b.
E178055
2.323,1.521 2.396,1.521 2.396,1.521 2.573,1.229 true 2.563,1.885 2.625,1.885 2.625,1.885 2.688,1.333 true 2.188,0.531 1.698,0.177 1.698,0.177 1.479,0.177 true 1.313,0.104 1.667,0.427 0.354,0.323 10 *1 2.146,1.448 2.531,1.823 0.385,0.375 10 *2 2.406,1.844 2.75,2.167 0.344,0.323 10 *3
*1 Second Claw
*2 Rear End Claw
*3 Rear End Stopper


Insert the wiper rubber into the front end of the wiper blade and slide it towards the rear end through the second claw.


c.

After pushing the wiper rubber through the rear end claw, allow it to stick out from the rear end stopper.


d.
E178056
1.24,0.208 1.385,0.208 1.385,0.208 1.625,0.531 true 1.063,0.146 1.51,0.552 0.448,0.406 10 *1
*1 Front End Claw


Slide the wiper rubber through the front end claw.


Hide 85212A 4.INSTALL REAR WIPER BLADE

a.
E236905

Push the wiper blade straight toward the left side of the vehicle to attach the claw and install the wiper blade to the wiper arm.

NOTICE:

Be careful not to damage the claw.



b.

Close the wiper blade holder.