Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH › 2011.11–2015.08
RM19Y0E _59 Vehicle Exterior _003019 WIPER / WASHER _0015276 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RHD)

a.
E139574
2.198,1.354 2.521,0.792 true 1.854,1.344 1.938,0.781 true 1.406,1.344 1.333,0.802 true 1.063,1.344 0.844,0.781 true 2.375,1.427 2.469,1.792 true 1.938,1.438 1.99,1.813 true 1.583,1.438 1.521,1.802 true 1.229,1.438 1.052,1.823 true 0.083,0.01 0.5,0.323 0.417,0.313 10 *a 1.948,1.823 2.323,2.156 0.375,0.333 10 1 1.833,0.573 2.323,0.917 0.49,0.344 10 +S 2.396,0.573 2.927,0.99 0.531,0.417 10 WB 1.25,0.573 1.667,0.875 0.417,0.302 10 W 0.917,1.823 1.448,2.167 0.531,0.344 10 WR 0.646,0.573 1.177,0.896 0.531,0.323 10 +1R 1.396,1.823 1.906,2.156 0.51,0.333 10 EW 2.438,1.823 2.854,2.167 0.417,0.344 10 2
*a Component without harness connected
(Windshield Wiper Switch Assembly)


Check the resistance.

i.

Measure the resistance and check the results in accordance with the value(s) in the tables below.

Standard Resistance (Front Wiper Switch):
Tester Connections Conditions Specified Conditions
4 (1) - 3 (WB) MIST Below 1Ω
5 (+S) - 4 (1) OFF
5 (+S) - 4 (1) INT
4 (1) - 3 (WB) LO
3 (WB) - 2 (2) HI


If the result is not as specified, replace the windshield wiper switch assembly.

Standard Resistance (Front Washer Switch):
Tester Connections Conditions Specified Conditions
7 (W) - 6 (EW) OFF 10 kΩor higher
7 (W) - 6 (EW) ON Below 1Ω


If the result is not as specified, replace the windshield wiper switch assembly.

Standard Resistance (Rear Wiper and Washer Switch):
Tester Connections Conditions Specified Conditions
9 (+1R) - 8 (WR) - 6 (EW) OFF 10 kΩor higher
8 (WR) - 6 (EW) WASH (Rear wiper switch OFF) Below 1Ω
9 (+1R) - 6 (EW) ON
9 (+1R) - 8 (WR) - 6 (EW) WASH (Rear wiper switch ON)


If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the intermittent operation.

i.

Connect the positive (+) voltmeter terminal to terminal 4 (1) and the negative (-) voltmeter terminal to terminal 6 (EW).


ii.

Connect the positive (+) battery lead to terminal 3 (WB) and the negative (-) battery lead to terminals 6 (EW).


iii.

Turn the wiper switch to the INT position.


iv.

Connect the positive (+) battery lead to terminal 5 (+S) for 5 seconds.


v.

Connect the negative (-) battery lead to terminal 5 (+S) to operate the intermittent wiper relay. Measure the voltage between terminals 4 (1) and 6 (EW).

Standard:

Refer to the illustration below.


E106356
2.729,0.042 3.156,0.438 0.427,0.396 10 *a 3.635,1.458 3.938,1.781 0.302,0.323 10 *e 1.521,0.781 1.906,1.177 0.385,0.396 10 *b 2.99,0.688 3.313,1 0.323,0.313 10 *c 3,1.135 3.396,1.5 0.396,0.365 10 *d
*a Connect the negative (-) battery terminal cable to terminal 5 (+S) *b Voltage between terminals 4 (1) and 6 (EW)
*c 11 to 14 V *d 0 V
*e 2.3 to 4.3 seconds - -


If the result is not as specified, replace the windshield wiper switch assembly.



c.

Check the operation of the front washer.

i.

Turn the wiper switch off.


ii.

Connect the positive (+) battery lead to terminal 3 (WB) and the negative (-) battery lead to terminals 5 (+S) and 6 (EW).


iii.

Connect the positive (+) voltmeter terminal to terminal 4 (1) and the negative (-) voltmeter terminal to terminal 6 (EW). Turn the washer switch on and off, and check the voltage between terminals 4 (1) and 6 (EW).

Standard:

Refer to the illustration below.


E106382
3.198,1.177 3.198,1.292 true 3.865,1.177 4.156,1.313 true 0.094,0.063 0.469,0.396 0.375,0.333 10 *a 1.365,0.802 1.813,1.25 0.448,0.448 10 *b 2.813,0.333 3.24,0.698 0.427,0.365 10 *c 2.823,0.573 3.219,0.958 0.396,0.385 10 *d 2.823,0.792 3.198,1.167 0.375,0.375 10 *e 2.823,1.031 3.167,1.375 0.344,0.344 10 *f 3.104,1.365 3.438,1.719 0.333,0.354 10 *g 4.229,1.292 4.573,1.635 0.344,0.344 10 *h
*a Washer Switch *b Voltage between terminals 4 (1) and 6 (EW)
*c ON *d OFF
*e 11 to 14 V *f 0 V
*g Approximately 0.3 seconds *h Approximately 2.2 seconds


If the result is not as specified, replace the windshield wiper switch assembly.



Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LHD)

a.
E139574
2.198,1.344 2.521,0.781 true 1.844,1.354 1.927,0.792 true 1.406,1.365 1.333,0.823 true 1.063,1.354 0.844,0.792 true 2.375,1.438 2.469,1.802 true 1.927,1.427 1.979,1.802 true 1.573,1.438 1.51,1.802 true 1.24,1.438 1.063,1.823 true 0.083,0.01 0.49,0.375 0.406,0.365 10 *a 1.271,0.615 1.604,0.865 0.333,0.25 10 1 1.375,1.823 1.823,2.167 0.448,0.344 10 +S 0.885,1.823 1.135,1.99 0.25,0.167 10 WB 1.938,1.833 2.323,2.115 0.385,0.281 10 W 2.458,0.625 2.865,0.917 0.406,0.292 10 WR 2.406,1.823 2.938,2.104 0.531,0.281 10 +1R 1.844,0.583 2.094,0.75 0.25,0.167 10 EW 0.781,0.615 1.115,0.865 0.333,0.25 10 2
*a Component without harness connected
(Windshield Wiper Switch Assembly)


Check the resistance.

i.

Measure the resistance and check the results in accordance with the value(s) in the tables below.

Standard Resistance (Front Wiper Switch):
Tester Connections Conditions Specified Conditions
7 (1) - 8 (WB) MIST Below 1Ω
6 (+S) - 7 (1) OFF
6 (+S) - 7 (1) INT
7 (1) - 8 (WB) LO
8 (WB) - 9 (2) HI


If the result is not as specified, replace the windshield wiper switch assembly.

Standard Resistance (Front Washer Switch):
Tester Connections Conditions Specified Conditions
4 (W) - 5 (EW) OFF 10 kΩor higher
4 (W) - 5 (EW) ON Below 1Ω


If the result is not as specified, replace the windshield wiper switch assembly.

Standard Resistance (Rear Wiper and Washer Switch):
Tester Connections Conditions Specified Conditions
2 (+1R) - 3 (WR) - 5 (EW) OFF 10 kΩor higher
3 (WR) - 5 (EW) WASH (Rear wiper switch OFF) Below 1Ω
2 (+1R) - 5 (EW) ON
2 (+1R) - 3 (WR) - 5 (EW) WASH (Rear wiper switch ON)


If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the intermittent operation.

i.

Connect the positive (+) voltmeter terminal to terminal 7 (1) and the negative (-) voltmeter terminal to terminal 5 (EW).


ii.

Connect the positive (+) battery lead to terminal 8 (WB) and the negative (-) battery lead to terminals 5 (EW).


iii.

Turn the wiper switch to the INT position.


iv.

Connect the positive (+) battery lead to terminal 6 (+S) for 5 seconds.


v.

Connect the negative (-) battery lead to terminal 6 (+S) to operate the intermittent wiper relay. Measure the voltage between terminals 7 (1) and 5 (EW).

Standard:

Refer to the illustration below.


E106356
2.729,0.042 3.156,0.438 0.427,0.396 10 *a 3.635,1.458 3.938,1.781 0.302,0.323 10 *e 1.521,0.781 1.906,1.177 0.385,0.396 10 *b 2.99,0.688 3.313,1 0.323,0.313 10 *c 3,1.135 3.396,1.5 0.396,0.365 10 *d
*a Connect the negative (-) battery terminal cable to terminal 5 (+S) *b Voltage between terminals 4 (1) and 6 (EW)
*c 11 to 14 V *d 0 V
*e 2.3 to 4.3 seconds - -


If the result is not as specified, replace the windshield wiper switch assembly.



c.

Check the operation of the front washer.

i.

Turn the wiper switch off.


ii.

Connect the positive (+) battery lead to terminal 8 (WB) and the negative (-) battery lead to terminals 6 (+S) and 5 (EW).


iii.

Connect the positive (+) voltmeter terminal to terminal 7 (1) and the negative (-) voltmeter terminal to terminal 5 (EW). Turn the washer switch on and off, and check the voltage between terminals 7 (1) and 5 (EW).

Standard:

Refer to the illustration below.


E106382
3.198,1.177 3.198,1.292 true 3.865,1.177 4.156,1.313 true 0.094,0.063 0.469,0.396 0.375,0.333 10 *a 1.365,0.802 1.813,1.25 0.448,0.448 10 *b 2.813,0.333 3.24,0.698 0.427,0.365 10 *c 2.823,0.573 3.219,0.958 0.396,0.385 10 *d 2.823,0.792 3.198,1.167 0.375,0.375 10 *e 2.823,1.031 3.167,1.375 0.344,0.344 10 *f 3.104,1.365 3.438,1.719 0.333,0.354 10 *g 4.229,1.292 4.573,1.635 0.344,0.344 10 *h
*a Washer Switch *b Voltage between terminals 4 (1) and 6 (EW)
*c ON *d OFF
*e 11 to 14 V *f 0 V
*g Approximately 0.3 seconds *h Approximately 2.2 seconds


If the result is not as specified, replace the windshield wiper switch assembly.