Home › Vehicle Exterior › LIGHTING (EXT) › FOG LIGHT ASSEMBLY
RM19Y0E _59 Vehicle Exterior _003020 LIGHTING (EXT) _0015283 FOG LIGHT ASSEMBLY N

LIGHTING (EXT)  FOG LIGHT ASSEMBLY  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

If there is a problem with the fog light aim, the cause of the problem may be an incorrectly installed bulb. Therefore, bulb installation should be checked prior to performing the adjustment procedure.



PROCEDURE

Hide 1. VEHICLE PREPARATION FOR FOG LIGHT AIMING ADJUSTMENT

a.

Prepare the vehicle:

·

Make sure that there is no damage or deformation of the body around the fog lights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the trunk and vehicle, making sure that the spare tire, tools and jack are also removed.

·

Have a person of average weight (75 kg, 165 lb) sit in the driver seat.



Hide 2. PREPARATION FOR FOG LIGHT AIMING

a.
E263301
1.073,1.365 1.479,1.708 0.406,0.344 10 *a 1.198,1.823 1.552,2.156 0.354,0.333 10 *b
*a 90°
*b 10 m (32.8 ft.) or 3 m (9.84 ft.)


Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 10 m (32.8 ft.) distance between the vehicle (fog light bulb center) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.


NOTICE:

A distance of 10 m (32.8 ft.) between the vehicle (fog light bulb center) and wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment (the target zone will change with the distance, so follow the instructions in the illustration).



b.

Prepare a piece of thick white paper approximately 2.0 m (6.56 ft.) (height) x 4.0 m (13.1 ft.) (width) to use as a screen.


c.

Draw a vertical line down the center of the screen (V line).


d.

Set the screen as shown in the illustration.

E257171
1.479,0.083 1.958,0.469 0.479,0.385 10 *A 5.125,0.073 5.573,0.51 0.448,0.438 10 *B 1.354,0.385 1.833,0.771 0.479,0.385 10 *a 1.406,1.292 1.885,1.677 0.479,0.385 10 *b 2.667,0.802 3.146,1.188 0.479,0.385 10 *c 0.531,2.948 1.01,3.333 0.479,0.385 10 *d 1.458,3.417 1.938,3.802 0.479,0.385 10 *e 5.031,3.469 5.448,3.771 0.417,0.302 10 *f 1.146,3.052 1.625,3.438 0.479,0.385 10 *g 4.948,0.385 5.427,0.771 0.479,0.385 10 *a 4.979,1.281 5.458,1.667 0.479,0.385 10 *b 6.177,0.792 6.656,1.177 0.479,0.385 10 *c 4.052,2.948 4.531,3.333 0.479,0.385 10 *d 4.719,3.083 5.198,3.469 0.479,0.385 10 *g 1.135,0.625 1.615,1.01 0.479,0.385 10 *g 4.688,0.656 5.167,1.042 0.479,0.385 10 *g
*A Aligning distance is 10 m (32.8 ft.) *B Aligning distance is 3 m (9.84 ft.)
*a V RH Line *b V LH Line
*c V Line *d H Line
*e 10 m (32.8 ft.) *f 3 m (9.84 ft.)
*g 90° - -


HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




e.
I033423
0.365,1.698 0.792,2.073 0.427,0.375 10 *e 2.792,0.875 3.188,1.271 0.396,0.396 10 *d 1.604,0.333 2.021,0.698 0.417,0.365 10 *b 1,0.333 1.385,0.698 0.385,0.365 10 *a 2.26,0.313 2.646,0.708 0.385,0.396 10 *c
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground


Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

HINT:

Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or name of the manufacturer marked on the fog light as the center mark.


i.

H line (Fog light height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.


ii.

V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):

Draw two vertical lines so that they intersect the H line at each center mark.



Hide 3.INSPECT FOG LIGHT AIMING

a.

Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.

NOTICE:

Do not keep the fog light covered for more than 3 minutes. The fog light lens is made of synthetic resin, which may melt or be damaged due to excessive heat.



b.

Start the engine.

NOTICE:

Engine speed must be 1500 or more.



c.

Turn on the fog light and check if the cutoff line falls within the specified area in the following illustration.

B117629
0.516,1.317 0.959,1.513 0.444,0.196 10 *c 1.634,0.174 2.082,0.37 0.449,0.196 10 *A 5.033,0.174 5.34,0.37 0.307,0.196 10 *B 1.761,0.787 1.917,0.968 0.156,0.182 10 *a 1.761,1.015 1.917,1.196 0.156,0.182 10 *b 3.003,2.079 3.159,2.26 0.156,0.182 10 *e 5.092,0.825 5.248,1.007 0.156,0.182 10 *a 5.092,1.054 5.248,1.235 0.156,0.182 10 *b 3.919,1.311 4.363,1.507 0.444,0.196 10 *c 2.664,1.657 3.034,2.062 false 6.345,2.079 6.501,2.26 0.156,0.182 10 *e 6.006,1.657 6.376,2.062 false
*A Aligning distance is 10 m (32.8 ft.) *B Aligning distance is 3 m (9.84 ft.)
*a V RH Line *b V LH Line
*c H Line *e Hot Zone



Hide 4.ADJUST FOG LIGHT AIMING

a.
E231765
0.771,2.802 2.052,3.094 true 2.073,3.042 2.438,3.365 0.365,0.323 10 *1
*1 Aiming Screw


Adjust the aim vertically:

Adjust the aim of each fog light to the specified range by turning the aiming screw with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it, and then retighten it so that the final turn of the screw is in the clockwise direction.