Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT DIMMER SWITCH › 2011.11–2015.08
RM19Y0E _59 Vehicle Exterior _003020 LIGHTING (EXT) _0015287 HEADLIGHT DIMMER SWITCH G

LIGHTING (EXT)  HEADLIGHT DIMMER SWITCH  INSPECTION  


PROCEDURE

Hide 84140 1.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for RHD)

a.
E218654
2.531,0.938 2.875,0.906 true 1.083,0.906 0.792,0.521 true 2.531,1.198 2.896,1.313 true 2.135,1.229 2.521,1.583 true 1.896,1.25 2.146,1.594 true 2.344,1.198 2.781,1.542 true 1.74,1.25 1.771,1.583 true 1.469,1.24 1.385,1.542 true 1.302,1.24 1.052,1.583 true 1.104,1.208 0.708,1.594 true 0.906,1.188 0.521,1.156 true 0.115,0.052 0.479,0.385 0.365,0.333 10 *a 2.927,0.844 3.323,1.24 0.396,0.396 10 L 0.667,0.365 1.167,0.74 0.5,0.375 10 B 2.979,1.26 3.396,1.594 0.417,0.333 10 B 2.51,1.604 2.969,1.958 0.458,0.354 10 E 2.844,1.542 3.313,1.875 0.469,0.333 10 B 2.156,1.615 2.583,1.99 0.427,0.375 10 L 1.74,1.625 2.229,1.979 0.49,0.354 10 HI 1.313,1.594 1.833,2.021 0.521,0.427 10 LO 0.927,1.625 1.344,1.948 0.417,0.323 10 LH 0.406,1.594 0.958,1.958 0.552,0.365 10 RL+ 0.25,1.073 0.771,1.417 0.521,0.344 10 RH
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the light control switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (B) - 6 (B),
6 (B) - 7 (E),
7 (E) - 8 (L)
Light control switch off 10 kΩ or higher
5 (B) - 8 (L) Light control switch tail Below 1 Ω
5 (B) - 8 (L) Light control switch head
6 (B) - 7 (E)




b.

Inspect the headlight dimmer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (B) - 7 (E),
7 (E) - 9 (HI)
Headlight dimmer switch flash Below 1 Ω
7 (E) - 9 (HI) Headlight dimmer switch high beam
7 (E) - 10 (LO) Headlight dimmer switch low beam


HINT:

Perform the flash and high beam inspection with the light control switch on head.




c.

Inspect the turn signal switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
12 (RL+) - 13 (RH) Turn signal switch right turn Below 1 Ω
11 (LH) - 12 (RL+),
12 (RL+) - 13 (RH)
Turn signal switch neutral 10 kΩ or higher
11 (LH) - 12 (RL+) Turn signal switch left turn Below 1 Ω




d.

Inspect the fog light switch (w/ Front Fog Light).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (L) - 3 (B) Fog light switch off 10 kΩ or higher
1 (L) - 3 (B) Front fog light switch on Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



Hide 84140 2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for LHD)

a.
E218654
0.917,0.948 0.573,0.917 true 2.302,0.906 2.604,0.531 true 0.896,1.208 0.542,1.323 true 1.292,1.229 0.906,1.583 true 1.469,1.229 1.188,1.583 true 1.094,1.219 0.656,1.563 true 1.688,1.229 1.656,1.563 true 1.917,1.25 2.01,1.563 true 2.146,1.229 2.396,1.563 true 2.344,1.229 2.729,1.615 true 2.531,1.208 2.917,1.188 true 0.115,0.073 0.51,0.542 0.396,0.469 10 *a 2.625,1.635 3.042,1.99 0.417,0.354 10 RL+ 2.271,1.635 2.646,2 0.375,0.365 10 RH 1.927,1.594 2.292,1.958 0.365,0.365 10 LO 1.552,1.604 1.927,1.917 0.375,0.313 10 HI 0.823,1.635 1.167,1.938 0.344,0.302 10 E 0.542,1.552 0.875,1.917 0.333,0.365 10 B 0.438,0.823 0.781,1.135 0.344,0.313 10 B 0.406,1.25 0.719,1.583 0.313,0.333 10 B 2.646,0.365 3.146,0.771 0.5,0.406 10 L 1.146,1.604 1.479,1.906 0.333,0.302 10 L 2.948,1.094 3.333,1.458 0.385,0.365 10 LH
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the light control switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
13 (B) - 12 (B),
12 (B) - 11 (E),
11 (E) - 10 (L)
Light control switch off 10 kΩ or higher
13 (B) - 10 (L) Light control switch tail Below 1 Ω
13 (B) - 10 (L) Light control switch head
12 (B) - 11 (E)




b.

Inspect the headlight dimmer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
12 (B) - 11 (E),
11 (E) - 9 (HI)
Headlight dimmer switch flash Below 1 Ω
11 (E) - 9 (HI) Headlight dimmer switch high beam
11 (E) - 8 (LO) Headlight dimmer switch low beam


HINT:

Perform the flash and high beam inspection with the light control switch on head.




c.

Inspect the turn signal switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (RL+) - 7 (RH) Turn signal switch right turn Below 1 Ω
5 (LH) - 6 (RL+),
6 (RL+) - 7 (RH)
Turn signal switch neutral 10 kΩ or higher
5 (LH) - 6 (RL+) Turn signal switch left turn Below 1 Ω




d.

Inspect the fog light switch (w/ Front Fog Light).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (L) - 4 (B) Fog light switch off 10 kΩ or higher
2 (L) - 4 (B) Front fog light switch on Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.