Home › Vehicle Exterior › LIGHTING (EXT) › TURN SIGNAL FLASHER ASSEMBLY › 2011.11–2015.08
RM19Y0E _59 Vehicle Exterior _003020 LIGHTING (EXT) _0015291 TURN SIGNAL FLASHER ASSEMBLY G

LIGHTING (EXT)  TURN SIGNAL FLASHER ASSEMBLY  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LHD and RHD vehicle.

·

The procedure listed below is for the RHD vehicle.



PROCEDURE

Hide 81980 1.INSPECT TURN SIGNAL FLASHER ASSEMBLY

a.
E239254C02
1.5,0.094 1.948,0.344 0.448,0.25 1.188,0.99 0.708,0.979 true 1.198,1.24 0.719,1.229 true 1.938,1.313 1.938,1.729 true 1.448,1.313 0.906,1.667 true 1.708,1.323 1.479,1.719 true 2.24,1.313 2.531,1.604 true 1.896,1.708 2.229,2.042 0.333,0.333 10 E 0.531,0.906 0.896,1.271 0.365,0.365 10 IG 1.604,0.135 2.073,0.51 0.469,0.375 10 E35 0.083,0.01 0.417,0.292 0.333,0.281 10 *a 0.698,1.615 1.083,1.938 0.385,0.323 10 EL 1.354,1.708 1.76,2.052 0.406,0.344 10 ER 2.427,1.615 3.052,1.958 0.625,0.344 10 EHW 0.583,1.167 0.938,1.531 0.354,0.365 10 B
*a Front view of wire harness connector
(to Turn Signal Flasher Assembly)


Disconnect the E35 turn signal flasher assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E35-1 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E35-4 (B) - Body ground Always 11 to 14 V


If the result is not as specified, repair or replace the wire harness or connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E35-5 (EL) - Body ground Turn signal switch off 10 kΩ or higher
Turn signal switch in left turn position Below 1 Ω
E35-6 (ER) - Body ground Turn signal switch in neutral position 10 kΩ or higher
Turn signal switch in right turn position Below 1 Ω
E35-7 (E) - Body ground Always Below 1 Ω
E35-8 (EHW) - Body ground Hazard warning switch off 10 kΩ or higher
Hazard warning switch on Below 1 Ω


If the result is not as specified, repair or replace the wire harness or connector or the headlight dimmer switch assembly.


d.
E239255C02
1.49,0.219 1.927,0.521 0.438,0.302 1.813,1.24 2.396,1.396 true 1.521,1.219 0.813,1.219 true 0.146,0.115 0.458,0.417 0.313,0.302 10 *a 1.573,0.281 2.052,0.583 0.479,0.302 10 E35 2.438,1.323 2.885,1.656 0.448,0.333 10 LR 0.646,1.146 1.01,1.542 0.365,0.396 10 LL
*a Front view of wire harness connector
(to Turn Signal Flasher Assembly)


Reconnect the E35 turn signal flasher assembly connector.


e.

Measure the voltage according to the valve(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E35-2 (LR) - Body ground Hazard warning switch off Below 1 V
Hazard warning switch on 11 to 14 V (60 to 120 times per minute)
Turn signal switch off Below 1 V
Ignition switch ON and turn signal switch in RH position 11 to 14 V (60 to 120 times per minute)
E35-3 (LL) - Body ground Hazard warning switch off Below 1 V
Hazard warning switch on 11 to 14 V (60 to 120 times per minute)
Turn signal switch off Below 1 V
Ignition switch ON and turn signal switch in LH position 11 to 14 V (60 to 120 times per minute)


If the result is not as specified, replace the turn signal flasher assembly.