Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM C

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P1730  Transmission Solenoid Power Supply  


DESCRIPTION

The battery supplies electricity to the TCM even when the ignition switch is off. This power allows the TCM to store data such as DTC history and freeze frame data. If the battery voltage falls below a minimum level, these memories are cleared and the TCM determines that there is a malfunction in the power supply circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P1730 Transmission Solenoid Power Supply Back-up power source (BAT, BAT2) is cut off for a specific period of time.
(1 trip detection logic)
·

Open or short in back-up power source circuit

·

TCM


Come on Blinks DTC stored

·

MIL:"Comes on" means the MIL (Malfunction Indicator Lamp) illuminates.

·

Memory:"DTC stored" means the TCM stores the trouble code if the ECU detects the DTC detection condition.


WIRING DIAGRAM

C246628E03
6.083,3.26 6.625,3.583 0.542,0.323 10 false TCM 1.604,1.208 2.49,1.677 0.885,0.469 10 false ECU-B 0.646,1.604 1.531,2.01 0.885,0.406 10 false FL MAIN 0.75,2.479 1.719,2.885 0.969,0.406 10 false BATTERY 5.781,1.063 6.365,1.417 0.583,0.354 10 false BAT2 5.781,1.792 6.323,2.156 0.542,0.365 10 false BAT 5.781,2.344 6.292,2.667 0.51,0.323 10 false E01 6.094,3.115 6.469,3.427 0.375,0.313 10 false E9 5.604,1.698 5.844,1.969 0.24,0.271 10 false 2 2,0.948 2.292,1.271 0.292,0.323 10 false 2 1.594,0.948 1.979,1.25 0.385,0.302 10 false 1 5.604,0.958 5.938,1.24 0.333,0.281 10 false 1 5.604,2.25 5.969,2.563 0.365,0.313 10 false 6

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK TCM (BAT, BAT2 VOLTAGE)
a.
C293875C01
1.552,0.229 1.969,0.479 0.417,0.25 1.104,2.365 1.583,1.865 true 2.073,2.74 1.865,1.875 true 2.354,2.375 1.958,1.865 true 0.208,0.188 0.563,0.458 0.354,0.271 10 false *a 1.677,0.281 2.031,0.552 0.354,0.271 10 false E9 0.677,2.385 1.323,2.729 0.646,0.344 10 false 6 (E01) 1.865,2.781 2.51,3.125 0.646,0.344 10 false 2 (BAT) 2.396,2.396 3.042,2.74 0.646,0.344 10 false 1 (BAT2)
*a Rear view of wire harness connector
(to TCM)


Disconnect the E9 TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E9-1 (BAT2) - E9-6 (E01) Always 11 to 14 V
E9-2 (BAT) - E9-6 (E01) Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E9-6 (E01) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ECU-B FUSE - TCM)
2.CHECK HARNESS AND CONNECTOR (ECU-B FUSE - TCM)
a.

Remove the ECU-B fuse from the engine room relay block.


b.

Disconnect the E9 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-B fuse terminal 2 - E9-1 (BAT2) Always Below 1 Ω
ECU-B fuse terminal 2 - E9-2 (BAT) Always Below 1 Ω
E9-1 (BAT2) or ECU-B fuse terminal 2 - Body ground Always 10 kΩ or higher
E9-2 (BAT) or ECU-B fuse terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK FOR INTERMITTENT PROBLEMS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR