Wear protective gloves. Sharp surfaces on the rear seat back frame sub-assembly and rear seat cushion spring assembly could cause injuries to your hands.
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.
71621A
1.INSTALL REAR SEAT CUSHION SILENCER PAD
Install the rear seat cushion silencer pad to the rear seat cushion pad.
71611A
2.INSTALL REAR SEAT CUSHION PAD
Install the rear seat cushion pad to the rear seat cushion spring assembly.
71075D
3.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER
| *1 | Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad with 14 new hog rings.
Do not soil or scratch the separate type rear seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.
| *1 | Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install the rear seat cushion spring assembly with 9 new hog rings.
Do not soil or scratch the separate type rear seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.
Close the fastener.
72695A
4.INSTALL REAR SEAT LOCK CONTROL CABLE (for Slide Seat Type)
| *1 | Band |
Engage the clamp.
Install the rear seat lock control cable with 2 new bands.
72695A
5.INSTALL REAR SEAT LOCK CONTROL CABLE (for Non-slide Seat Type)
| *1 | Band |
Engage the 2 clamps.
Install the rear seat lock control cable with a new band.
72695A
6.INSTALL REAR SEAT LOCK CONTROL CABLE (w/ Rear Seat Cushion Cover)
| *1 | Band |
Engage the clamp.
Install the rear seat lock control cable with 2 new bands.
7.INSTALL REAR NO. 1 SEAT CUSHION OUTER LEG (for Non-slide Seat Type)
| *1 | E-Ring |
| *2 | Pin |
| *3 | Rear No. 1 Seat Turn Spring |
Install the rear No. 1 seat turn spring and rear No. 1 seat cushion outer leg with the E-ring and pin.
8.INSTALL REAR NO. 1 SEAT CUSHION INNER LEG (for Non-slide Seat Type)
Use the same procedures as for the rear No. 1 seat cushion outer leg.
72160C
9.INSTALL REAR NO. 1 SEAT OUTER TRACK ASSEMBLY (except for Non-slide Seat Type)
Install the rear No. 1 seat outer track assembly with the 2 bolts.
72170C
10.INSTALL REAR NO. 1 SEAT INNER TRACK ASSEMBLY (except for Non-slide Seat Type)
Use the same procedures as for the rear seat outer track assembly.
71308E
11.INSTALL REAR SEAT LEG SUB-ASSEMBLY (except for Non-slide Seat Type)
Install the rear seat leg sub-assembly with the 3 nuts.
72670B
12.INSTALL REAR SEAT CUSHION LOCK ASSEMBLY (for Slide Seat Type)
| *1 | Rear Seat Lock Control Cable |
Install the rear seat cushion lock assembly with the 2 bolts.
Engage the clamp and connect the rear seat lock control cable.
72670B
13.INSTALL REAR SEAT CUSHION LOCK ASSEMBLY (for Non-slide Seat Type)
| *1 | Rear Seat Lock Control Cable |
Install the rear seat cushion lock assembly with the 2 bolts.
Engage the clamp and connect the rear seat lock control cable.
72670B
14.INSTALL REAR SEAT CUSHION LOCK ASSEMBLY (w/ Rear Seat Cushion Cover)
| *1 | Rear Seat Lock Control Cable |
Install the rear seat cushion lock assembly with the 2 bolts.
Engage the clamp and connect the rear seat lock control cable.
72670B
15.INSTALL REAR SEAT OUTER CUSHION LOCK ASSEMBLY (w/ Rear Seat Cushion Cover)
| *1 | Rear Seat Lock Control Cable |
Install the rear seat outer cushion lock assembly with the 2 bolts.
Engage the clamp and connect the rear seat lock control cable.
73330C
16.INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY
72665C
17.INSTALL REAR SEAT LOCK COVER (for Slide Seat Type)
Install the rear seat lock cover with the 2 screws.
72694
18.INSTALL REAR SEAT LOCK COVER (for Non-slide Seat Type)
Install the rear seat lock cover with the 2 screws.
72995
19.INSTALL REAR SEAT CUSHION COVER (w/ Rear Seat Cushion Cover)
Install the rear seat cushion cover with the 4 screws.
79959
20.INSTALL REAR SEAT LEG COVER (for Slide Seat Type)
Install the rear seat cushion and rear seat leg cover with the screw.
71324A
21.INSTALL REAR SEAT CUSHION (for Non-slide Seat Type)
Install the rear seat cushion with the screw.
72159A
22.INSTALL REAR SEAT TRACK BRACKET COVER (for Slide Seat Type)
Engage the 2 claws to install the rear seat track bracket cover.
Use the same procedure for the other rear seat track bracket covers.
71671A
23.INSTALL REAR SEAT BACK SILENCER PAD A
Install the rear seat back silencer pad A to the separate type rear seat back pad.
71651S
24.INSTALL SEPARATE TYPE REAR SEAT BACK PAD
Install the separate type rear seat back pad to the rear seat back frame sub-assembly.
71077S
25.INSTALL SEPARATE TYPE REAR SEAT BACK COVER
| *1 | Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install the separate type rear seat back cover to the separate type rear seat back pad with 13 new hog rings.
Do not soil or scratch the separate type rear seat back cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat back cover.
| *1 | Hook |
Attach the hook and close the fastener.
71956B
26.INSTALL REAR SEAT HEADREST SUPPORT
| *1 | Protruding Portion |
Align the protruding portions of the rear seat headrest support with the installation grooves of the rear seat back frame sub-assembly.
Attach the 2 claws to install the rear seat headrest support.
71956B
27.INSTALL REAR SEAT HEADREST SUPPORT ASSEMBLY
| *1 | Protruding Portion |
Align the protruding portion of the rear seat headrest support assembly with the installation groove of the rear seat back frame sub-assembly.
Attach the 2 claws to install the rear seat headrest support assembly.
71940A
28.INSTALL REAR SEAT HEADREST ASSEMBLY
| *1 | Lock Button |
Push in the lock button of the rear seat headrest support assembly and install the rear seat headrest assembly.
29.INSTALL REAR NO. 1 SEAT BACK ASSEMBLY
| *1 | E-Ring |
| *2 | Bushing |
Install the bushing.
Install the rear No. 1 seat back assembly with the 2 bolts and E-ring.
71878A
30.INSTALL REAR SEAT INNER RECLINING COVER
Engage the claw to install the seat inner reclining cover.
79011
31.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY
Engage the 4 claws to install the No. 1 seat cushion cover sub-assembly.
Install the 2 screws.
71833D
32.INSTALL REAR SEAT RECLINING COVER
Engage the 2 claws to install the rear seat reclining cover.
Install the screw.
72637A
33.INSTALL REAR SEAT LOCK HANDLE
| *1 | Snap Ring |
Install the rear seat lock handle with a new snap ring.