Wear protective gloves. Sharp surfaces on the No. 2 seat back frame sub-assembly and No. 2 seat cushion spring assembly could cause injuries to your hands.
79165
1.INSTALL REAR NO. 2 SEAT LEG BRACKET RH
| *1 | E-Ring |
| *2 | Bushing |
| *3 | Pin |
Install the rear No. 2 seat leg bracket RH with the E-ring, 2 bushings and pin.
79166
2.INSTALL REAR NO. 2 SEAT LEG BRACKET LH
Use the same procedure as for the RH side.
71622A
3.INSTALL REAR SEAT CUSHION SILENCER PAD B
Install the rear seat cushion silencer pad B to the No. 2 seat cushion pad sub-assembly.
79035A
4.INSTALL NO. 2 SEAT CUSHION PAD SUB-ASSEMBLY
Install the No. 2 seat cushion pad sub-assembly to the No. 2 seat cushion spring assembly.
79021A
5.INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY
| *1 | Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly to the No. 2 seat cushion pad sub-assembly with 6 new hog rings.
Do not soil or scratch the No. 2 seat cushion cover sub-assembly.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 2 seat cushion cover sub-assembly.
| *1 | Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install 13 new hog rings.
Do not soil or scratch the No. 2 seat cushion cover sub-assembly.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 2 seat cushion cover sub-assembly.
Close the fastener.
79107D
6.INSTALL REAR NO. 2 SEAT LEG SUB-ASSEMBLY
| *1 | E-Ring |
| *2 | Pin |
Install the rear No. 2 seat leg sub-assembly with the 2 E-rings and 2 pins.
Install the 2 tension springs.
72680C
7.INSTALL REAR NO. 2 SEAT CUSHION LOCK ASSEMBLY
Install the rear No. 2 seat cushion lock assembly with the 2 bolts.
73350
8.INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY
79952
9.INSTALL NO. 2 SEAT CUSHION COVER
Install the 2 No. 2 seat cushion covers with the 2 screws.
10.INSTALL NO. 2 SEAT CUSHION
Install the 2 No. 2 seat cushions with the 2 screws.
71393
11.INSTALL REAR SEAT CUSHION BAND
Install the rear seat cushion band with the screw.
71672
12.INSTALL REAR SEAT BACK SILENCER PAD B
Install the rear seat back silencer pad B to the No. 2 seat back pad sub-assembly RH.
Use the same procedure for the LH side and RH side.
79037A
13.INSTALL NO. 2 SEAT BACK PAD SUB-ASSEMBLY RH
Install the No. 2 seat back pad sub-assembly RH to the No. 2 seat back frame sub-assembly RH.
79038A
14.INSTALL NO. 2 SEAT BACK PAD SUB-ASSEMBLY LH
Use the same procedure as for the RH side.
79023
15.INSTALL NO. 2 SEAT BACK COVER SUB-ASSEMBLY RH
| *1 | Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install the No. 2 seat back cover sub-assembly RH to the No. 2 seat back pad sub-assembly RH with 3 new hog rings.
Do not soil or scratch the No. 2 seat back cover sub-assembly RH.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 2 seat back cover sub-assembly RH.
| *1 | Hook |
Engage the hook and close the fastener.
79024
16.INSTALL NO. 2 SEAT BACK COVER SUB-ASSEMBLY LH
Use the same procedure as for the RH side.
71931C
17.INSTALL REAR NO. 2 SEAT HEADREST SUPPORT
| *1 | Protruding Portion |
Align the protruding portions of the rear No. 2 seat headrest support with the installation grooves of the No. 2 seat back frame sub-assembly.
Engage the 2 claws to install the rear No. 2 seat headrest support.
Use the same procedure for both sides.
71931C
18.INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY
| *1 | Protruding Portion |
Align the protruding portion of the rear No. 2 seat headrest support assembly with the installation groove of the No. 2 seat back frame sub-assembly.
Engage the 2 claws and install the rear No. 2 seat headrest support assembly.
Use the same procedure for the both sides.
71970
19.INSTALL REAR SEAT HEADREST ASSEMBLY
| *1 | Lock Button |
Push in the lock button of the rear seat headrest support assembly and install the rear seat headrest assembly.
Use the same procedure for the both sides.
20.INSTALL REAR NO. 2 SEAT BACK ASSEMBLY RH
| *1 | Bushing |
Install the bushing and rear No. 2 seat back assembly RH.
21.INSTALL REAR NO. 2 SEAT BACK ASSEMBLY LH
Use the same procedure as for the RH side.
71303B
22.INSTALL REAR NO. 2 SEAT HINGE SUB-ASSEMBLY RH
| *1 | Bushing |
Install the rear No. 2 seat back hinge sub-assembly RH with the 3 bolts and bushing.
71304B
23.INSTALL REAR NO. 2 SEAT HINGE SUB-ASSEMBLY LH
Use the same procedure as for the RH side.
79273
24.INSTALL NO. 2 SEAT HINGE COVER
Install the No. 2 seat hinge cover with the 2 screws.
71485
25.INSTALL REAR SEAT HINGE COVER
Use the same procedure as for the No. 2 seat hinge cover.