Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/o Rear Heated Oxygen Sensor) › 2014.04–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014987 SFI SYSTEM(w/o Rear Heated Oxygen Sensor) U

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/o Rear Heated Oxygen Sensor)  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

By reading the Data List displayed on the GTS, values can be checked, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.


NOTICE:

In the table below, the values listed under Normal Condition are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.


HINT:

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
T terminal T terminal status OFF / ON - -
HINT:

Stored as Freeze Frame Data : Yes


Number of diagnosis codes Number of detected DTCs Min.: 0, Max.: 255 0 -
HINT:

Stored as Freeze Frame Data : Yes


O2 sensor signal Status of air-fuel ratio lean / rich - -
HINT:

Stored as Freeze Frame Data : Yes


Output volt of FR O2 SSR Heated oxygen sensor output voltage Min.: 0 V, Max.: 1.275 V 0.1 to 0.95 V:
Driving (50 km/h, 31 mph)
-
HINT:

Stored as Freeze Frame Data : Yes


Total fuel trim bank 1 Total fuel trim (average value for fuel trim system) Min.: 0, Max.: 2 - Total fuel trim bank 1 = Short term fuel trim bank 1 + Long term fuel trim bank 1
HINT:

Stored as Freeze Frame Data : Yes


Short term fuel trim bank 1 Short-term fuel trim Min.: -100 %, Max.: 100 % -20 to 20 %: Engine speed constant 2500 rpm Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
HINT:

Stored as Freeze Frame Data : Yes


Short term of FR O2 SSR Short-term fuel trim associated Min.: -100 %, Max.: 100 % -20 to 20 %:
Engine speed constant 2500 rpm
-
HINT:

Stored as Freeze Frame Data : Yes


Long term fuel trim bank 1 Long-term fuel trim Min.: -100 %, Max.: 100 % -30 to 30 %: Engine speed constant 2500 rpm Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value
HINT:

Stored as Freeze Frame Data : Yes


VF monitor VF monitor Min.: 0.75, Max.: 1.248 less than 1: rich condition
more than 1: lean condition
-
HINT:

Stored as Freeze Frame Data : Yes


Injection volume Injection volume of No. 1 cylinder (cumulative value for 10 times) Min.: 0 ml, Max.: 2 ml 0.003 to 0.015 ml: Idling Read value with A/C OFF and shift lever in N
HINT:

Stored as Freeze Frame Data : Yes


Injection time Injection period of No. 1 cylinder Min.: 0 ms, Max.: 32.64 ms 3 to 8 ms: Idling with cold engine
2 to 4 ms: Idling with warmed up engine
-
HINT:

Stored as Freeze Frame Data : Yes


Calculated load value Load calculated by ECM Min.: 0 %, Max.: 100 % 10 to 20 %: Idling (A/C OFF, neutral position) -
HINT:

Stored as Freeze Frame Data : Yes


Battery voltage Battery voltage Min.: 0 V, Max.: 65 V 11 to 14 V: Idling -
HINT:

Stored as Freeze Frame Data : Yes


Vehicle speed Vehicle speed Min.: 0 km/h, Max.: 255 km/h Actual vehicle speed -
HINT:

Stored as Freeze Frame Data : Yes


Engine revolution speed Engine speed Min.: 0 rpm, Max.: 16384 rpm 700 to 800 rpm (neutral position): Idling -
HINT:

Stored as Freeze Frame Data : Yes


Manifold absolute pressure Manifold absolute pressure Min.: 0 kPa, Max.: 255 kPa 70 to 104 kPa: Ignition switch ON (engine not started)
20 to 40 kPa: Idling
If value approximately 0 kPa:
·

PIM circuit short


If value 120 kPa or more:
·

VCPM circuit open or short

·

PIM circuit open

·

E2PM circuit open


HINT:

Stored as Freeze Frame Data : Yes


Barometric pressure Atmospheric pressure Min.: 0 kPa, Max.: 255 kPa Equivalent to atmospheric pressure (absolute pressure) -
HINT:

Stored as Freeze Frame Data : Yes


Intake air temperature Intake air temperature Min.: -40°C, Max.: 215°C Equivalent to temperature at location of manifold absolute pressure sensor
·

If value -30°C (-22°F) or less: sensor circuit open

·

If value 130°C (266°F) or more: sensor circuit shorted


HINT:

Stored as Freeze Frame Data : Yes


Engine coolant temperature Engine coolant temperature Min.: -40°C, Max.: 215°C 80 to 102°C (176 to 215°F): After warming up engine
·

If value -30°C (-22°F) or less: sensor circuit open

·

If value 130°C (266°F) or more: sensor circuit shorted


HINT:

Stored as Freeze Frame Data : Yes


Trip at Overheat fail-safe operation Number of trips overheat fail-safe operation Min.: 0, Max.: 65535 0 -
HINT:

Stored as Freeze Frame Data : Yes


Stop lamp signal Stop light switch OFF / ON ON: Brake pedal depressed
OFF: Brake pedal released
-
HINT:

Stored as Freeze Frame Data : Yes


Brake negative pressure switch Brake negative pressure switch OFF / ON ON: Brake pedal depressed (operate with ignition switch ON)
OFF: Idling (without load)
-
HINT:

Stored as Freeze Frame Data : Yes


Ignition timing advance Ignition timing advance for No. 1 cylinder Min.: -64°CA, Max.: 63.5°CA BTDC 0 to 10°CA (neutral position): Idling Read value with A/C OFF and shift lever in N
HINT:

Stored as Freeze Frame Data : Yes


Knock corr. advance angle Knock control correction advance angle Min.: -64 CA, Max.: 1984 CA 0 to 3 CA: Idling -
HINT:

Stored as Freeze Frame Data : Yes


Knock Feedback Value Knock feedback value Min.: -64 CA, Max.: 1984 CA - -
HINT:

Stored as Freeze Frame Data : Yes


Throttle Position Throttle valve opening angle Min.: 0°, Max.: 500° - -
HINT:

Stored as Freeze Frame Data : Yes


Absolute throttle position Absolute throttle position sensor Min.: 0 %, Max.: 100 %
·

0 to 15 %: Throttle fully closed

·

70 to 100 %: Throttle fully open


Read value with ignition switch ON (Do not start engine)
HINT:

Stored as Freeze Frame Data : Yes


Relative throttle position Relative throttle position sensor Min.: 0 %, Max.: 100 % 0 to 10 %: Idling Calculated value based on VTH
HINT:

Stored as Freeze Frame Data : Yes


Target idle speed Target idle speed Min.: 0 rpm, Max.: 51200 rpm 700 to 800 rpm (neutral position): Idling -
HINT:

Stored as Freeze Frame Data : No


Idle switch position Whether or not throttle position sensor detecting idle OFF / ON ON: Idling -
HINT:

Stored as Freeze Frame Data : Yes


ISC step ISC step Min.: 0 step, Max.: 255 step Depending on engine running condition -
HINT:

Stored as Freeze Frame Data : Yes


ISC duty ration Idle speed control valve control duty ratio Min.: 0 %, Max.: 100 % - -
HINT:

Stored as Freeze Frame Data : Yes


ISC Flow Flow rate calculated using information from manifold absolute pressure sensor Min.: 0 L/s, Max.: 80 L/s - -
HINT:

Stored as Freeze Frame Data : Yes


ISC Feedback Value ISC feedback amount Min.: -10 L/s, Max.: 70 L/s - -
HINT:

Stored as Freeze Frame Data : Yes


ISC learning value ISC learned airflow value Min.: 0 L/s, Max.: 80 L/s 0.4 to 1.23 L/s: Idling -
HINT:

Stored as Freeze Frame Data : Yes


Electric Load Feedback Val Compensation flow rate according to electrical load Min.: -10 L/s, Max.: 70 L/s - -
HINT:

Stored as Freeze Frame Data : Yes


Air Conditioner FB Val Compensation flow rate according to air conditioner load Min.: 0 L/s, Max.: 80 L/s - -
HINT:

Stored as Freeze Frame Data : Yes


Evaporative purge output Purge VSV control duty Min.: 0 %, Max.: 100 % 0 to 40 %: Idling -
HINT:

Stored as Freeze Frame Data : Yes


Purge corr. coefficient Purge correction coefficient Min.: -50 %, Max.: 350 % 0: Idling with warmed up engine -
HINT:

Stored as Freeze Frame Data : Yes


Evap Purge Flow Purge flow Min.: 0 %, Max.: 102.398 % - -
HINT:

Stored as Freeze Frame Data : Yes


VVT Advance Fail VVT advance fail OFF / ON OFF -
HINT:

Stored as Freeze Frame Data : Yes


VVT control VVT control OFF / ON - -
HINT:

Stored as Freeze Frame Data : Yes


Target angle of intake cam VVT target angle Min.: 0°CA, Max.: 640°CA 0 to 5°CA: Idling
10 to 40°CA: 2000 rpm (fixed speed)
-
HINT:

Stored as Freeze Frame Data : Yes


Actual angle of intake cam VVT change angle Min.: 0°CA, Max.: 640°CA 0 to 5°CA: Idling
10 to 40°CA: 2000 rpm (fixed speed)
-
HINT:

Stored as Freeze Frame Data : Yes


TVVT angle converted val. VVT calculated angle Min.: 0°CA, Max.: 640°CA 15 to 52°CA: Idling
15 to 82°CA: 2000 rpm (fixed speed)
-
HINT:

Stored as Freeze Frame Data : Yes


VVT control duty ratio VVT OCV control duty Min.: 0 %, Max.: 400 % 20 to 50 %: 2000 rpm (fixed speed) -
HINT:

Stored as Freeze Frame Data : Yes


Distance from DTC Cleared Distance from DTC cleared Min.: 0 km, Max.: 65535 km Distance driven after DTCs cleared -
HINT:

Stored as Freeze Frame Data : Yes


Warmup Cycle Cleared DTC Warmup cycle cleared DTC Min.: 0, Max.: 255 - -
HINT:

Stored as Freeze Frame Data : Yes


Engine Starting Time Time elapsed before engine starts (after starter turns on until engine speed reaches 400 rpm) Min.: 0 ms, Max.: 1048560 ms - -
HINT:

Stored as Freeze Frame Data : Yes


Starter Signal Starter signal OFF / ON ON: Starter operating
OFF: Starter not operating
-
HINT:

Stored as Freeze Frame Data : Yes


Engine Speed (Starter Off) Engine speed when starter off Min.: 0 rpm, Max.: 51200 rpm - -
HINT:

Stored as Freeze Frame Data : Yes


Starter Count Number of times starter turned on after ignition switch turned to ON Min.: 0, Max.: 255 - -
HINT:

Stored as Freeze Frame Data : Yes


Minimum Engine Speed Minimum engine speed Min.: 0 rpm, Max.: 51200 rpm - -
HINT:

Stored as Freeze Frame Data : Yes


Engine Start Hesitation History of hesitation during engine start OFF / ON - -
HINT:

Stored as Freeze Frame Data : Yes


Low Rev for Eng Start History of low engine speed after engine start OFF / ON - -
HINT:

Stored as Freeze Frame Data : Yes


Neutral Control Neutral control OFF / ON - -
HINT:

Stored as Freeze Frame Data : Yes


Run Dist of Previous Trip Distance driven during previous trip Min.: 0 km, Max.: 655.35 km - -
HINT:

Stored as Freeze Frame Data : Yes


Previous Trip Coolant Temp Engine coolant temperature during previous trip Min.: -40°C, Max.: 119.4°C - -
HINT:

Stored as Freeze Frame Data : Yes


Previous Trip Intake Temp Intake air temperature during previous trip Min.: -40°C, Max.: 119.4°C - -
HINT:

Stored as Freeze Frame Data : Yes


Misfire Avg. RPM Engine speed for average misfire range Min.: 0 rpm, Max.: 6375 rpm - -
HINT:

Stored as Freeze Frame Data : Yes


Misfire Avg. Load Engine load for average misfire range Min.: 0 g/rev, Max.: 3.98 g/rev - -
HINT:

Stored as Freeze Frame Data : Yes


Cylinder #1 Misfire Count Misfire counter for No. 1 cylinder Min.: 0 count, Max.: 255 count 0 -
HINT:

Stored as Freeze Frame Data : Yes


Cylinder #2 Misfire Count Misfire counter for No. 2 cylinder Min.: 0 count, Max.: 255 count 0 -
HINT:

Stored as Freeze Frame Data : Yes


Cylinder #3 Misfire Count Misfire counter for No. 3 cylinder Min.: 0 count, Max.: 255 count 0 -
HINT:

Stored as Freeze Frame Data : Yes


Cylinder #4 Misfire Count Misfire counter for No. 4 cylinder Min.: 0 count, Max.: 255 count 0 -
HINT:

Stored as Freeze Frame Data : Yes


All cylinder Misfire Count Misfire counter for all cylinders Min.: 0 count, Max.: 255 count 0 to 35 -
HINT:

Stored as Freeze Frame Data : Yes


Misfire Count parameter Misfire count parameter Min.: 0 count, Max.: 32767.5 count 0 -
HINT:

Stored as Freeze Frame Data : Yes


Misfire Margin Misfire margin Min.: -1 times, Max.: 0.992 times - -
HINT:

Stored as Freeze Frame Data : Yes


Fuel Cut Elps Time Elapsed time since fuel cut due to high engine speed Min.: 0 s, Max.: 65535 s - -
HINT:

Stored as Freeze Frame Data : Yes


Fuel pump relay Status of the fuel pump relay OFF / ON ON: fuel pump relay ON -
HINT:

Stored as Freeze Frame Data : Yes


Fuel Cut Condition Fuel cut condition OFF / ON ON: Fuel cut operating -
HINT:

Stored as Freeze Frame Data : Yes


Idle Fuel Cut Fuel cut at idle OFF / ON ON: Fuel cut operating -
HINT:

Stored as Freeze Frame Data : Yes


Immobiliser Fuel Cut Fuel cut condition OFF / ON ON: Fuel cut operating -
HINT:

Stored as Freeze Frame Data : Yes


Immobiliser Communication Immobiliser communication OFF / ON OFF -
HINT:

Stored as Freeze Frame Data : Yes


Electric load Electrical load status OFF / ON ON: Tail light switch ON
ON: Defogger switch ON
-
HINT:

Stored as Freeze Frame Data : Yes


Electric Fan Motor Electric fan motors operation status OFF / ON ON: Electric fan motor operating -
HINT:

Stored as Freeze Frame Data : Yes


Power steering signal Power steering signal OFF / ON ON: When turning steering wheel -
HINT:

Stored as Freeze Frame Data : Yes


Air conditioner signal A/C switch status OFF / ON ON: A/C ON -
HINT:

Stored as Freeze Frame Data : Yes


A/C Evap Temperature A/C Evap Temperature Min.: -80°C, Max.: 943.98°C Approximately the same temperature as the vehicle cabin. Internal ventilation, MAX COOL, air conditioning is off and blower is on. -
HINT:

Stored as Freeze Frame Data : No


A/C refrigerant pressure sensor A/C refrigerant pressure sensor Min.: 0 MPa, Max.: 1023.98 MPa 0 MPa (0 kgf/cm2) to 3.18 MPa (32 kgf/cm2): Ignition switch ON -
HINT:

Stored as Freeze Frame Data : No


Neutral start switch Neutral start switch ON / OFF - -
HINT:

Stored as Freeze Frame Data : Yes


Shift position P range P range signal OFF / ON - -
HINT:

Stored as Freeze Frame Data : Yes


Shift position R range R position signal OFF / ON - -
HINT:

Stored as Freeze Frame Data : Yes


Shift position 2 range 2 position signal OFF / ON - -
HINT:

Stored as Freeze Frame Data : Yes


Shift position L range L position signal OFF / ON - -
HINT:

Stored as Freeze Frame Data : Yes


Shift position N range N position signal OFF / ON - -
HINT:

Stored as Freeze Frame Data : Yes


Shift position D range D position signal OFF / ON - -
HINT:

Stored as Freeze Frame Data : Yes


Gear position Gear position signal received from transmission control ECU 1st / 2nd / 3rd / 4th - -
HINT:

Stored as Freeze Frame Data : Yes


Turbine speed Turbine speed Min.: 0 rpm, Max.: 12750 rpm - -
HINT:

Stored as Freeze Frame Data : Yes


Lock up condition Lock up condition OFF / ON - -
HINT:

Stored as Freeze Frame Data : Yes




ACTIVE TEST


HINT:

Performing an Active Test enables components including the relays, Vacuum switching valve and actuators, to be operated without removing any parts. The Active Test can be performed with the GTS. Performing an Active Test as the first step of troubleshooting is one method of shortening diagnostic time.


Data List can be displayed during Active Test.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Active Test.


g.

According to the display on the GTS, perform the Active Test.

Powertrain > Engine > Active Test
Tester Display Control Range Inspection Item Diagnostic Note
ISC Min.: 10 step, Max.: 100 step Idle speed control valve (stepper motor) Vehicle: Stationary
Engine speed: Idling
Battery voltage: 8.5 V or more
Fuel pump ON or OFF Fuel pump relay (F/P relay) -
Purge VSV 0 % or 100 % Vacuum switching valve (EVAP) -
A/C magnet clutch relay OFF or ON Air conditioner magnet clutch -
Radiator fan OFF or ON Radiator fan motor ON: Forced operation (at first stage only*)
Terminal T OFF or ON Turn on and off EFIT and E connection ON: EFIT and E terminals of DLC3 are connected.
OFF: EFIT and E terminals of DLC3 are disconnected.

*: w/ Cooling Fan Resistor