Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY › 2014.04–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015085 AUTOMATIC TRANSMISSION ASSEMBLY A

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 84248A 1.INSTALL SWITCH HARNESS CLAMP

a.

Connect the park/neutral position switch connector clamp.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


b.

Install the switch harness clamp with the 2 bolts.


Hide 32000 2.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C248816

Engage the splines of the input shaft and turbine runner.


b.
C248817

Engage the splines of the stator shaft and the stator while turning the torque converter assembly.

HINT:

If the stator shaft splines are difficult to engage with the stator splines, move the torque converter back approximately 10 mm (0.394 in.) and engage the splines while rotating the torque converter.



c.
C248818

Turn the torque converter assembly to insert the key of the oil pump drive gear into the groove of the torque converter assembly.


d.

Clean the torque converter set bolt holes.


e.
C267374C02
1.198,0.365 1.604,0.198 true 1.25,1.646 1.75,1.865 true 2.521,0.927 2.635,0.75 false 2.875,0.688 3.042,0.625 false 1.604,0.083 1.969,0.406 0.365,0.323 10 *1 2.375,0.906 2.74,1.229 0.365,0.323 10 *1 1.781,1.802 2.271,2.167 0.49,0.365 10 *2 3.094,0.552 3.427,1 0.333,0.448 10 *2
*1 Engine Surface
*2 Drive Plate Surface


Using a vernier caliper and a straightedge, measure dimension A between the transmission contact surface of the engine and the torque converter contact surface of the drive plate.


f.
C153933N01
2.635,1.656 3.115,2.083 0.479,0.427 10 B

Using a vernier caliper and a straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the step above.

Standard:

A + 16.5 mm (0.650 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the transmission is installed to the engine with the torque converter not sufficiently inserted, the torque converter may be damaged.

·

Do not include the thickness of the set block.




g.

Apply MP grease to the torque converter tip.


Hide 51022 3.INSTALL REAR ENGINE SUPPORT MEMBER SUB-ASSEMBLY

a.

Install the rear engine support member sub-assembly and automatic transmission assembly with the 3 bolts.

Torque:
37 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 35000 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C249326C02
1.604,1.083 2.552,0.771 true 2.594,0.688 3.094,1.125 0.5,0.438 10 *1 0.906,1 1.396,1.448 0.49,0.448 10 *2
*1 Torque Converter Centerpiece
*2 Crankshaft


Apply clutch spline grease around the crankshaft contact surface with the torque converter centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum spread:

Approximately 1 g (0.0353 oz)



b.

Hang the oil cooler tube sub-assembly from the automatic transmission using a piece of string.


c.
C256731C02
0.969,3.021 0.604,2.667 false 1.26,2.698 1.427,2.531 false 2.76,1.323 2.573,1.323 true 1.5,0.344 1.677,0.177 true 2.104,4.448 2.552,4.667 0.448,0.219 12 C 2.469,4.385 2.927,4.667 0.458,0.281 12 C 0.958,4.448 1.448,4.667 0.49,0.219 12 C 0.646,4.219 1.188,4.615 0.542,0.396 12 C 0.49,3.646 1.01,4.104 0.521,0.458 12 A 0.51,3.167 1.01,3.635 0.5,0.469 12 A 0.865,2.5 1.313,2.969 0.448,0.469 12 A 2.188,2.344 2.708,2.74 0.521,0.396 12 A 2.875,3.396 3.302,3.792 0.427,0.396 12 B 1.667,0.042 2.198,0.448 0.531,0.406 10 *1 2.792,1.24 3.271,1.677 0.479,0.438 10 *1 1.448,2.417 1.917,2.823 0.469,0.406 10 *2 0.438,2.531 0.948,2.948 0.51,0.417 10 *2
*1 Knock Pin
*2 Wire Harness Clamp Bracket


Install the automatic transmission assembly and wire harness clamp bracket with 4 bolts A and other 5 bolts.

Torque:
Bolts A, B : 39 N*m (398 kgf*cm, 29 ft.*lbf)
Bolt C : 37 N*m (375 kgf*cm, 27 ft.*lbf)

Bolt length:

57 mm (2.244 in.) for bolt A

50 mm (1.969 in.) for bolt B

40 mm (1.575 in.) for bolt C


NOTICE:
·

Since seal bolts should be used at positions A, be sure to use new bolts.

·

Confirm that 2 knock pins are on the transmission fitting surface of the engine block before installation.

·

After installing the transmission, confirm that the torque converter rotates smoothly.




d.

Install the torque converter mounting bolts.

Torque:
28 N*m (280 kgf*cm, 20 ft.*lbf)

HINT:

First install the silver blue bolt and then the remaining 5 black bolts.



Hide 35013 7.INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

a.

Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it onto the transmission oil filler tube sub-assembly.


b.

Install the transmission oil filler tube sub-assembly with the bolt.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


Hide 35103 8.INSTALL TRANSMISSION OIL LEVEL DIPSTICK SUB-ASSEMBLY

a.

Install the transmission oil level dipstick sub-assembly.


Hide 10.INSTALL ENGINE AND TRANSMISSION ASSEMBLY (for 3SZ-VE)

Hide 11.INSTALL ENGINE AND TRANSMISSION ASSEMBLY (for K3-VE)